The influence of sheet metal anisotropy on laser forming process

Journal of Manufacturing Science and Engineering

Volumn 127, Issue 3, 2005, Pages 572-582

  Cheng, Peng ^a   Yao, Y Lawrence ^a  

^a Department of Earth and Environmental Sciences   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

ANISOTROPY; CHARACTERIZATION; COLD ROLLING; COMPUTER SIMULATION; FORMING; PLASTIC DEFORMATION; TEXTURES;

COLD-ROLLED SHEET METAL; LASER FORMING PROCESS; ORIENTATION DISTRIBUTION FUNCTION (ODF); SHEET METAL ANISOTROPY;

SHEET METAL;

EID: 24744440961     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1949620     Document Type: Article

References (20)

1. Scully, K., 1987, "Laser Line Heating," J. Ship Prod., 3(4), pp. 237-246.
2. Vollertsen, F., 1994, "Mechanisms and Models for Laser Forming," Laser Assisted Net Shape Engineering, Proceedings of the LANE'94, B. Meisenbach, ed., 1, pp. 345-360.
3. Sprenger, A., Vollertsen, F., Steen, W. F., and Watkins, K., 1994, "Influence of Strain Hardening on Laser Bending," Laser Assisted Net Shape Engineering, Proceedings of the LANE'94, B. Meisenbach, ed., 1, pp. 361-370.
4. Li., W., and Yao, Y. L., 2000, "Numerical and Experimental Study of Strain Rate Effects in Laser Forming," ASME J. Manuf. Sci. Eng., 122, pp. 445-451.
5. Cheng, J., and Yao, Y. L., 2002, "Microstructure Integrated Modeling of Multiscan Laser Forming," ASME J. Manuf. Sci. Eng., 124, pp. 379-388.
6. Liao, K. C., Friedman, P. A., Pan, J., and Tang, S. C., 1998, "Texture Development and Plastic Anisotropy of B. C. C. Strain Hardening Sheet Metals," Int. J. Solids Struct., 35(36), pp. 5205-5236.
7. Hill, R., 1948, "A Theory of the Yielding and Plastic Flow of Anisotropic Metals," Proc. R. Soc. London, Ser. A, 193, p. 281.
8. Gotoh, M., 1977, "A Theory of Plastic Anisotropy Based on a Yield Function of Fourth Order (Plane Stress State)-I and II," Int. J. Mech. Sci., 19, pp. 505-520.
9. Barlat, F., and Lian, J., 1989, "Plastic Behavior and Stretch Ability of Sheet Metals Part I: A Yield Function for Orthotropic Sheet under Plane Stress Conditions," Int. J. Plast., 5, p. 51.
10. Hill, R., 1990, "Constitutive Modeling of Orthotropic Plasticity in Sheet Metals," J. Mech. Phys. Solids, 38, pp. 405-417.
11. Hosford, W. F., 1996, "On the Crystallographic Basis of Yield Criteria," Textures Microstruct., 26-27, pp. 479-493.
12. Taylor, G. I., 1938, "Plastic Strain in Metals," J. Inst. Met., 62, pp. 307-324.
13. Kocks, U. F., and Chandra, H., 1982, "Slip Geometry in Partially Constrained Deformation," Acta Metall., 30, pp. 695-709.
14. Gilormini, P., 1989, "The Theory of Rate Sensitive Pencil Glide Application to Rolling Textures," Acta Metall., 37(7), pp. 2093-2101.
15. Kocks, W. K., Tome, C. N., and Wenk, H. R., 1998, Texture and Anisotropy-Preferred Orientations in Polystals and Their Effects on Material Properties, Cambridge University Press, London, pp. 48-112.
16. Raabe, D., and Lucke, K., 1994, "Rolling and Annealing Textures of BCC Metals," Mater. Sci. Forum, 157-162, pp. 597-610.
17. Raabe, D., 1995, "Simulation of Rolling Textures of b.c.c. Metals Considering Grain Interactions and Crystallographic Slip on {110}, {112}, and {123} Planes," Mater. Sci. Eng., A, 197, pp. 31-37.
18. ASTM, 2002, "Metals Test Methods and Analytical Procedures," Annual Book of ASTM Standards, 03.01, ASTM International, Philadelphia, PA.
19. Daniel, D., and Jonas, J. J., 1990, "Measurement and Prediction of Plastic Anisotropy in Deep-Drawing Steels," Metall. Trans. A, 21A, pp. 331-343.
20. Bao, J., and Yao, Y. L., 2001, "Analysis and Prediction of Edge Effects in Laser Bending," ASME J. Manuf. Sci. Eng., 123, pp. 53-61.