Revisiting the physical properties of thermomechanical pulp

ATIP. Association Technique de L'Industrie Papetiere

Volumn 58, Issue 2, 2004, Pages 11-17

  Law, Kwei Nam ^a  

^a UNIVERSITÉ DU QUÉBEC À TROIS RIVIÈRES   (Canada)

Author keywords

[No Author keywords available]

Indexed keywords

COMPOSITION; DELAMINATION; ENERGY EFFICIENCY; PULP REFINING; RAW MATERIALS; SOFTWOODS;

FIBER BREAKAGE; FIBER SEPARATION; REFINING TECHNOLOGY; VOLUMETRIC COMPRESSION;

THERMOMECHANICAL PULP;

CHEMICAL COMPOSITION; DELAMINATION; RAW MATERIALS; REFINING; SOFTWOODS; THERMOMECHANICAL PULPING;

EID: 2442608723     PISSN: 09977554     EISSN: None     Source Type: Trade Journal    
DOI: None     Document Type: Article

References (41)

1. Corson, S.R, Aspects of mechanical pulp fibre separation and development in a disc refiner. Paperi ja Puu 7:801-814 (1989).
2. Corson, S.R., Process impacts on mechanical pulp fibre and sheet dimensions. Pulp Paper Can. 103(2):20-27 (2002).
3. Karnis, A. The mechanism of fibre development in mechanical pulping. J. Pulp Paper Sci. 20(10):J280-J288 (1994).
4. Heitner, C., Beatson, R.P. and Atack, D. Ultra-high-yield pulping. Part V. High compression impregnation of softwood chips with sodium sulphite - A method of producing CMP with high wet and dry strength. Proc. Intl. Mech. Pulp. Conf.:101-108 (1985).
5. Barbe, M.C., Janknecht, SW. and Sauriol, J.F. The importance of chip impregnation on refiner pulp quality. Proc. Ann. Meetg. CPPA (PAPTEC):A155-A175 (1994).
6. Renaud, M., Rueff, M. and Rocaboy, A.C. Mechanical behaviour of saturated wood under compression. Part 2.; Behaviour of wood at low rates of strain - Some effects of compression on wood structure. Wood Sci. and Techn. 30:237-243 (1996).
7. Peng, F., and Granfeldt, T. Changes in the microstructure of spruce wood chips after screw press treatment. J. Pulp Paper Sci. 22(4):J140-J145 (1966).
8. Law, K.N., Lanouette, R. and Yang, K.C. A new approach to mechanical pulping. Tappi J. 83(9):63 (published online, 12 pages) (2000).
9. Law, K.N., Lanouette, R. and Yang, K.C. Effect of chip compression on refining energy and pulp quality of birch TMP. Appita J. 53(4):296-299, 291 (200).
10. Law, K.N. and Yang, K.C. Characteristics of fibre separation in wood loaded by normal-to-grain compression. Appita J. (in press, Nov. 2002),
11. Sabourin, M., Vaughn, J., Wiseman, N., Cort, J.B., and Galtti, P., Mill scale results on TMP pulping of southern pine with pressurized chip pretreatment. Proc. 87th Ann. Meetg. PAPTAC:C9-C16 (2001).
12. Mohlin, U.-B. Fibre development during mechanical pulp refining. J. Pulp Paper Sci. 23(1):J28-J33 (1997).
13. Reme, P.A., Johnsen, P.O. and Helle, T. Changes induced in early- and latewood by mechanical pulp refining. Nordic Pulp Paper Res. J. 14(3):256-262 (1999).
14. Law, K.N. Mechanical behavior of early- and latewood under compression load. Proc. Intl. Mech. Pulp. Conf.:159166 (2001).
15. Murton, K.D., Richardson, J.D., Corson, S.R. and Diffy, G. IMP refining of Radiata pine earlywood and latewood fibres. Proc. Intl. Mech. Pulp. Conf.:361-371 (2001).
16. Casey, J.P. (editor). Pulp and Paper Chemistry and chemical technology, 3rd ed., Vol. 1. John Wiley & Sous, N.Y., pp:249 (1980).
17. Heikkurinen, A. and Leskelä, L. The character and properties of mechanical pulps, In: Papermaking Science and Technology, Book 5 - Mechanical pulping, Sundholm J. (editor), Finnish Paper Engineers' Association and TAPPI, pp: 394-421 (1999).
18. Leask R.A. Pulp Quality. In: Pulp and Paper Manufacture, Vol. 2 - Mechanical Pulping, Joint Textbook Committee of the Paper Industry, pp: 138-164 (1987).
19. Lindholm, C.-A., and Kurdin, J.A., Chemimeclianical pulping, In: Papermaking Science and Technology, Book 5 - Mechanical pulping, Sundholm J. (editor), Finnish Paper Engineers' Association and TAPPI, pp: 238 (1999).
20. Giertz, H., Basic wood raw material properties and their significance in mechanical pulping. Intl. Mech. Pulp. Conf. Session 1, 1:1-15 (1977).
21. Chang, H.M., Sinkey, J., and Van, J., Chemical analysis of refiner pulps. Tappi J.:62(9):103-106 (1979).
22. Forgacs, O.L. The characterization of mechanical pulps. Pulp & Paper Mag. Can. (Conv. Issue):T89-T118 (1963).
23. Valade, J.L., Law, K.N., Lanouette, R. and Marchand, A comparative study on BCTMP. Research Report, Pulp and Paper Research Center, Université du Québec à Trois-Rivières, 46 pages, Nov. 1995.
24. Kibblewhite, P.R. Fibres and fines of some radiata pine corewood and slab-wood thermomechancial and refinermechanical pulps. Appita J. 37(8):650-657 (1984).
25. Leask, R.A. Mechanical Pulping. In: Pulp and Paper Manufacture, Vol. 2, Technical editor: R. A. Leask. Joint Textbook Committee of the Paper Industry, pp. 149-150 (1987).
26. Johansson, L., Peng, F.F., Simonson, R. and Granfeldt,T.The affect of screw-press pre-treatment in CTMP pulping process. Proc. Intl. Mech. Pulp. Conf:.371-375 (1997).
27. Kure, K.A. and Dahlqvist, G. Development of structural fibre properties in high intensity refining. Prroc. Ann. Meetg., PAPTAC:B213-B218 (1998).
28. Jones, T.G. Ttacheid properties control TMP and PRMP pulp properties. Proc. Intl. Mech. Pulp. Conf.:97122 (1999).
29. Kure, K.A., Sabourin, M.J., Dahlqvist, G. and Helle, T. Adjusting refining intensity by changing refiner plate design and rotational speed effects on structural fibre properties. Proc. Ann. Meetg., PAPTAC:B59-B65 (1999).
30. Mohlin, U.-B. Properties of TMP fractions and their importance for the quality of printing papers. Part 2. The influence of particle properties and particle size distribution on pulp properties. Svensk Papperstidning 83(16):513-519 (1980).
31. De Choudens, C., and Angelier, R. Bleached high yield pulps with the Bivis process constituted of two Bivis machines in line. Das Papier 43(10A):V8-V12 (1989).
32. Mokvist, A., Jackson, M., Heikurinen, A., Court, G. and Li Z. The production of SC and LWC pulps on large capacity conical disc refining systems. Proc. Intl. Mech. Pulp. Conf.:239-251, Helsinki, June 4-8, 2001.
33. Shallhorn, P., and Karnis, A.,Tear and tensile strength of mechanical pulps. Proc. Intl. Mech. Pulp. Conf.:25-36 (1979).
34. Mohlin, U.-B., Fibre bonding ability a key pulp quality parameter for mechanical pulps to be used in printing papers, Proc. Intl. Mech. Pulp. Conf.:49-57 (1989).
35. Honkasalo, J., Knuts, K., Laine, E.J., and Nygren-Kontinen, A., The fines fraction of mechanical pulp. Paperi ja Puu 11:693-698 (1983).
36. Li, H., Ni, Y. and Sain, M., Characterization of BCTMP fines and their effect on sizing. Tappi J. 1(7):3-7 (2002).
37. Stationwala, M.I., Mathieu, J. and Karnis, A., On the interaction of wood and mechanical pulping equipment. Part I, Fibre development and generation of fines. J. Pulp Paper Sci. 22(5):J155-J160 (1996).
38. Luukko, K. and Paulapura, H., Development of fines quality in the TMP process. Preprints 84th Ann. Meetg. of Tech. Sect. CPPA (PAPTAC):B23-B27 (1998).
39. Law, K.N. The role of fibrillar elements in thermomechanical pulp. Pulp Paper Can. 101(1):57-60 (2000).
40. Law, K.N. Rethinking chip refining. Proc. 54th Appita Ann. Conf.:101-106 (2000).
41. Law, K.N. On the refining mechanism. Tappi J. 1(1):1-4 (2002).