SEWHAPM: Development of a water hydraulic axial piston motor for underwater tool systems

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science

Volumn 219, Issue 7, 2005, Pages 639-656

  Nie, S L ^a   Huang, G H ^b   Zhu, Y Q ^a   Li, Z Y ^a   Li, Y P ^b  

^a HUAZHONG UNIVERSITY OF SCIENCE AND TECHNOLOGY   (China)

^b UNIVERSITY OF REGINA   (Canada)

Author keywords

Axial piston motor; Concentric gap damper; Global moment balanced; Hydrostatic slipper bearing; Plate valve; Water hydraulics

Indexed keywords

DAMPING; HYDRAULICS; HYDROSTATIC BEARINGS; LUBRICATION; MATHEMATICAL MODELS; MINERAL OILS; PISTONS; RIGIDITY; TORQUE; UNDERWATER EQUIPMENT; VALVES (MECHANICAL);

AXIAL PISTON MOTOR; CONCENTRIC GAP DAMPER; GLOBAL MOMENT BALANCED; HYDROSTATIC SLIPPER BEARING; PLATE VALVE; WATER HYDRAULICS;

HYDRAULIC MOTORS;

AXIAL PISTON MOTOR; HYDRAULIC EQUIPMENT; HYDROSTATIC BEARING;

EID: 24144470794     PISSN: 09544062     EISSN: None     Source Type: Journal    
DOI: 10.1243/095440605X31409     Document Type: Article

References (30)

1. Backé, W. Water- or oil-hydraulics in the future. In Proceedings of 6th Scandinavian International Conference on Fluid Power, Finland, 26-28 May 1999, pp. 51-64.
2. Trostmann, E. Hydraulic components using tap water as pressure medium. In Proceedings of 4th Scandinavian International Conference on Fluid Power, Finland, 26-29 September 1995, pp. 942-954.
3. Seabrook, C. and Burrows, C. R. Water hydraulics-some design challenges. FPST-Vol. 1, Collected Papers, ASME 1994, pp. 59-63.
4. Bhushan, B. and Gray, S. Investigation of material combinations under high load and speed in synthetic seawater. Lubr. Eng., 1979, 35(11), 628-635.
5. Bech, T., Olsen, S., and Klit, P. Design of pumps for water hydraulic systems. In Proceedings of 6th Scandinavian International Conference on Fluid Power, Finland, 26-28 May 1999, pp. 231-242.
6. Brookes, C. A. Tribological application of ceramic materials in water hydraulics: potentials and problems. Design, Modelling and Control of Pumps, 1998 (Research Studies Press, Hull).
7. Takashima, M., Said, K., and Yuge, A. Development of high performance components for pollution free water hydraulic system. In Proceedings of 3rd JHPS International Symposium on Fluid Power, Japan, 1996, pp. 49-54.
8. Trostmann, E. Water Hydraulics Control Technology, 1996 (Marcel Dekker, Inc., New York).
9. Terävä, J., Kuikko, T., and Vilenius, M. Development of seawater hydraulic power pack. In Proceedings of 4th Scandinavian International Conference on Fluid Power, Finland, 26-29 September 1995, pp. 978-991.
10. Brookes, C. A., Fagan, M. J., James, R. D., Kerry, P., and McConnachie, J. The development of water hydraulic pumps using advanced engineering ceramics. In Proceedings of 4th Scandinavian International Conference on Fluid Power, Finland, 26-29 September 1995, pp. 965-977.
11. Brookes, C. A., Fagan, M. J., James, R. D., and McConnachie, J. The selection and performance of ceramic components in a seawater pump. In Proceedings of 3rd JHPS International Symposium on Fluid Power, Japan, 1996, pp. 3-12.
12. Fagan, M. J. and McConnachie, J. Water Hydraulics, 1995 (University of Hull, UK).
13. Fagan, M. J. and McConnachie, J. Modelling and analysis techniques used in the design of axial piston pumps for water hydraulics, modeling and simulation. 6th Bath International Fluid Power Workshop, 1993, pp. 34-45.
14. Pohls, O., Rantanen, O., and Kuikko, T. Seawater hydraulic axial piston machine. In Proceedings of 6th Scandinavian International conference on Fluid Power, Finland, 26-28 May 1999, pp. 219-229.
15. Tammisto, J., Koskinen, K. T., and Pohls, O. Development of water hydraulic arc-cylinder pump and motor prototypes. In Proceedings of 6th Scandinavian International Conference on Fluid Power, Finland, 26-28 May 1999, pp. 207-217.
16. Nie, S. L. Research on seawater axial piston type motor made of new type engineering materials (in chinese). PhD Dissertation, HUST, 2002.
17. Webster, J. and McGee, J. A. An investigation into a modified port-plate seal of an axial piston pump. Wear, 1988, 127, 85-99.
18. Sheng, J. C. Hydraulic Hydrodynamics, 1980 (China Machine Press, Beijing).
19. Nie, S. L. and Li, Z. Y. Work principle and characteristic analyses of hydrostatic bearing. Chinese J. Mech. Eng., 2002, 15(2), 162-166.
20. Xu, Y. M. Oil Lubrication Theory And Design of Friction Pairs in Hydraulic Pump And Motor, 1987 (China Machine Press, Beijing).
21. Zhai, P. X. Design of Swash Plate Type Axial Piston Hydraulic Pump, 1978 (China Coal Industry Press, Beijing).
22. Xu, S. W. Plunger Pumps, 1985 (China Machine Press, Beijing).
23. Graham, R. and Hastings, G. G. Development of a seawater hydraulic tool system. AD-A114960/8, May 1982.
24. Clarke, C. G. and Allen, C. The water lubricated, sliding wear behavior of polymeric materials against steel. Tribol. Int., 1991, 24(2), 109-118.
25. Hicks, D. C. and Pleass, C. M. Development and testing of a composite/plastic high-pressure seawater pump. In Proceedings of NCFP, USA, 1986, 69-78.
26. Schöpke, M. and Feldmann, D. G. Ceramics in Axial Piston Pumps and Motors. In Proceedings of 4th International Conference on Fluid Power Transmission and Control, Hangzhou, China, 1997, pp. 584-594.
27. Zhang, S. W. State of art of polymer tribology. Tribol. Int., 1998, 31(1-3), 49-60.
28. Li, K. Y. and Hooke, C. J. A note on the lubrication of composite slippers in water-based axial piston pumps and motors. Wear, 1991, 147, 431-437.
29. Li, Z., Yang, S., Yu, Z., and He, X. Development of hydraulic pump to operate with raw water. In Proceedings of ASME Fluids Engeering Summer Meeting (CD-ROM Version), USA, 21-25 June 1998.
30. Hooke, C. J. and Li, K. Y. The lubrication of overclamped slippers in axial piston pumps: centrally loaded behaviour. Proc. Instn Mech. Engrs, Part C: J. Mechanical Engineering Science, 1988, 202(C2), 287-293.