Edge machining effects on the failure of polymer matrix composite coupons

Composites Part A: Applied Science and Manufacturing

Volumn 35, Issue 7-8, 2004, Pages 989-999

  Ghidossi, Patrick ^a   El Mansori, Mohamed ^a   Pierron, Fabrice ^a  

^a ENSAM Laboratoire de Mecanique et Procedes de Fabrication JE 2381   (France)

Author keywords

A. Polymer matrix composites (PMCs); E. cutting; E. Machining; Mechanical testing

Indexed keywords

COST EFFECTIVENESS; CUTTING; ELASTIC MODULI; EPOXY RESINS; MACHINING; STRENGTH OF MATERIALS; SURFACE ROUGHNESS; TENSILE TESTING;

INDUSTRIAL COMPOSITE COMPONENTS; MACHINING OPERATIONS; POLYMER-MATRIX COMPOSITES (PMC);

COMPOSITE MATERIALS;

EID: 2342626513     PISSN: 1359835X     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.compositesa.2004.01.015     Document Type: Conference Paper

References (20)

1. Wang D., Ramulu M., Arola D. Orthogonal cutting mechanisms of graphite/epoxy composite. Part I: unidirectional laminates. Int J Machine Tools Manufacture. 35:(12):1995;1623-1638.
2. Test method for tensile properties of fiber-resin composites. 1976;American Society for the Testing of Materials.
3. Practice for in-plane shear stress-strain response of unidirectional. 1976;American Society for the Testing of Materials.
4. Test method for compressive properties of unidirectional or cross-ply fiber-resin composites. 1987;American Society for the Testing of Materials.
5. Standard method for shear properties of composite materials by the V-notched beam method. 1993;American Society for the Testing of Materials.
6. Plastiques: préparation des éprouvettes par usinage. 1997;AFNOR.
7. Guégan P. Contribution à la qualification de l'usinage de matériaux composites à matrice organique (Contribution to the assessment of the machining of polymer matrix composites). PhD thesis, Nantes University; 1994.
8. Tagliferri V., Caprino G., Ditterlizzi A. Effect of drilling parameters on the finish and mechanical properties of gfrp composites. Int J Mach Tools Manufacture. 30:(1):1990;77-84.
9. Persson E., Eriksson I., Zackrisson L. Effect of hole machining defects on strength and fatigue life of composite laminates. Composites Part A. 28:1997;141-151.
10. Capello E., Tagliaferri V. Drilling damage of GFRP and residual mechanical behaviour - Part II: static and cyclic bearing load. J Compos Technol Res. 23:(2):2001;131-137.
11. Arola D., Ramulu M. Machining-induced surface texture effects on the flexural properties of a graphite/epoxy laminate. Composites. 25:(8):1994;822-834.
12. Arola D., Ramulu M. Net-shape machining and the process-dependent failure of fiber-reinforced plastics under static loads. J Compos Technology Res. 20:(4):1998;210-220.
13. Arola D., Ramulu M. Net-shape manufacturing and the performance of polymer composites under dynamic loads. Exp Mech. 37:(4):1996;379-385.
14. Ramulu M, Arola D. private communication; 2003.
15. Eriksen E. The influence of surface roughness on the mechanical strength properties of machined short-fibre-reinforced thermoplastics. Compos Sci Technol. 60:2000;107-113.
16. Pierron F. New Iosipescu fixture for the measurement of the in-plane shear modulus of laminated composites: design and experimental procedure. Technical Report, No. 940125, Ecole des Mines de Saint-Etienne; 1994.
17. Pierron F. Saint-Venant effects in the Iosipescu specimen. J Compos Mater. 32:(22):1998;1986-2015.
18. Pierron F., Vautrin A. Measurement of the in-plane shear strength of unidirectional composites with the Iosipescu test. Composit Sci Technol. 57:(12):1997;1653-1660.
19. Gibson A., Wu Y., Longmuir A., Chandler H. Delamination of curved composite shells due to through-thickness tensile stresses. Plast Rubber Compos. 19:(1):1993;39-46.
20. Pierron F, Davies P. Ring compression test for cylindrical composite mechanical characterization, vol. 4. In: European Conference on Composite Materials-Composite Testing and Standardisation; 1998. p. 193-202. 31 August to 2 September in Lisbon, Portugal.