Cooling the tip of a turbine blade using pressure side holes - Part II: Heat transfer measurements

Journal of Turbomachinery

Volumn 127, Issue 2, 2005, Pages 278-286

  Christophel, J R ^a   Thole, K A ^a   Cunha, F J ^b  

^a State University   (United States)

^b PRATT AND WHITNEY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COOLING; DURABILITY; HEAT FLUX; HEAT TRANSFER; LEAKAGE (FLUID); OXIDATION; WIND TUNNELS;

ADIABATIC EFFECTIVENESS; FILM-COOLANT INJECTION; LEAKAGE FLOW; LOW-SPEED WIND TUNNEL;

TURBOMACHINE BLADES;

HEAT EXCHANGER;

EID: 21444456314     PISSN: 0889504X     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1811096     Document Type: Article

References (21)

1. Kwak, J. S., and Han, J. C., 2002, "Heat Transfer Coefficient on the Squealer Tip and Near Squealer Tip Regions of a Gas Turbine Blade," ASME Int. Mech. Eng. Congress and Exposition, ASME Paper No. IMECE 2002-32109.
2. Christophel, J., Thole, K. A., and Cunha, F., 2005, "Cooling the Tip of a Turbine Blade Using Pressure Side Holes-Part I: Adiabatic Effectiveness Measurements," ASME J. Turbomachinery, 127, pp. 270-277.
3. Mayle, R. E., and Metzger, D. E., 1982, "Heat Transfer at the Tip of an Unshrouded Turbine Blade," Proc. 7th Int. Heat Transfer Conference 3, ASME, New York, pp. 87-92.
4. Morphis, G., and Bindon, J. P., 1988, "Effect of Relative Motion, Blade Edge Radius and Gap Size on the Blade Tip Pressure Distribution in an Annular Turbine Cascade With Clearance," ASME Paper No. 88-GT-256.
5. Bindon, J. P., 1989, "The Measurement and Formation of Tip Clearance Loss," ASME J. Turbomach., 111, pp. 257-263.
6. Bunker, R. S., 2000, "A Review of Turbine Blade Tip Heat Transfer," Turbine 2000 Symposium on Heat Transfer in Gas Turbine Systems, Cesme, Turkey.
7. Bunker, R. S., Bailey, J. C., and Ameri, A. A., 2000, "Heat Transfer and Flow on the First-Stage Blade Tip of a Power Generation Gas Turbine: Part I - Experimental Results," ASME J. Turbomach., 122, pp. 263-271.
8. Jin, P., and Goldstein, R. J., 2003, "Local Mass/Heat Transfer on a Turbine Blade Tip," Int. J. Rotating Mach., 9(2), pp. 981-995.
9. Azad, G. S., Han, J. C., and Boyle, R. J., 2000, "Heat Transfer and Presure Distributions on a Gas Turbine Blade Tip," ASME J. Turbomach., 122, pp. 717-724.
10. Teng, S., Han, J. C., and Azad, G., 2001, "Detailed Heat Transfer Coefficient Distributions on a Large-Scale Gas Turbine Blade Tip," ASME J. Heat Transfer, 123, pp. 803-809.
11. Kwak, J. S., and Han, J. C., 2002, "Heat Transfer Coefficient and Film-Cooling Effectiveness on a Gas Turbine Blade Tip," ASME Turbo Expo, Amsterdam, The Netherlands. Paper No. GT2002-30194.
12. Saxena, V., Nasir, H., and Ekkad, S. V., 2003, "Effect of Blade Tip Geometry on Tip Flow and Heat Transfer For a Blade in a Low Speed Cascade," ASME Paper No. GT2003-38176.
13. Ameri, A. A., 2001, "Heat Transfer and Flow on the Blade Tip of a Gas Turbine Equipped With a Mean-Camberline Strip," ASME Paper No. GT2001-0156.
14. Kim, Y. W., and Metzger, D. E., 1995, "Heat Transfer and Effectiveness on Film Cooled Turbine Blade Tip Models," ASME J. Turbomach., 117, pp. 12-21.
15. Kim, Y. W., Downs, J. P., Soechting, F. O., Abdel-Messeh, W., Steuber, G., and Tanrikut, S., 1995, "A Summary of the Cooled Turbine Blade Tip Heat Transfer and Film Effectiveness Investigations Performed by Dr. D. E. Metzger," ASME J. Turbomach., 117, pp. 1-11.
16. Hohlfeld, E. M., Christophel, J. R., Couch, E. L., and Thole, K. A., 2003, "Predictions of Cooling From Dirt Purge Holes Along the Tip of a Turbine Blade," ASME Turbo Expo, Atlanta, Georgia. Paper No. GT2003-38251.
17. Moffat, R. J., 1988, "Describing the Uncertainties in Experimental Results," Exp. Therm. Fluid Sci., 1, pp. 3-17.
18. Gnielinski, V., 1976, "New Equations for Heat and Mass Transfer in Turbulent Pipe and Channel Flow," Int. Chem. Eng., 16, pp. 359-368.
19. Kakaç, S., Shah, R. K., and Aung, W., 1997, Handbook of Single-Phase Convective Heat Transfer, Wiley, New York, pp. 34-35.
20. Kays, W. M., and Crawford, M. E., 1980, Convective Heat and Mass Transfer, Second Edition, McGraw-Hill, New York, pp. 269-270.
21. Sen, B., Schmidt, D. L., and Bogard, D. G., 1996, "Film Cooling With Compound Angle Holes: Heat Transfer," ASME J. Turbomach., 118, pp. 800- 806.