Technologies for ITER divertor vertical target plasma facing components

Nuclear Fusion

Volumn 45, Issue 6, 2005, Pages 512-518

  Schlosser, J ^a   Escourbiac, F ^a   Merola, M ^b   Fouquet, S ^a   Bayetti, P ^a   Cordier, J J ^a   Grosman, A ^a   Missirlian, M ^a   Tivey, R ^c   Rodig M ^d  

^a IRFM   (France)

^b EFDA CLOSE SUPPORT UNIT   (Germany)

^c International Thermonuclear Experimental Reactor ITER Garching   (Germany)

^d FORSCHUNGSZENTRUM JÜLICH   (Germany)

Author keywords

[No Author keywords available]

Indexed keywords

CARBON FIBERS; DEBONDING; HEAT FLUX; METAL CASTING; PLASMA DEVICES; RESIDUAL STRESSES; TARGETS; THERMAL EXPANSION;

CARBON FIBER COMPOSITES (CFC); INFRARED THERMOGRAPHY; MONOBLOCKS; PLASMA FACING COMPONENTS (PFC);

FUSION REACTOR DIVERTORS;

EID: 21144470154     PISSN: 00295515     EISSN: None     Source Type: Journal    
DOI: 10.1088/0029-5515/45/6/013     Document Type: Article

References (20)

1. Schlosser J. et al 2003 High heat flux testing impact on the Tore Supra toroidal pumped limiter achievement Proc. 20th IEEE/NPSS/SOFE (San-Diego, 2003) p 92
2. van Houtte D. et al 2004 Real time control of fully non-inductive operation in Tore Supra leading to 6 minutes, 1 GJ plasma discharges Proc. 23rd SOFT (Venice, 2004) Fusion Eng. Des. submitted
3. Schlosser J. et al 1995 In-service experience feedback of the Tore Supra actively cooled inner first wall Fusion Eng. Des. 27 203-9
4. Schlosser J. et al 2002 Material properties and consequences on the quality of Tore Supra plasma facing components J. Nucl. Mater. 307-311 686-90
5. Huber T. et al 1995 The manufacturing and testing of the toroidal pumped limiter prototype elements for Tore Supra Proc. 16th SOFE (Champaign, 1995) p 716
6. Cordier J.J. et al 2003 The Tore Supra toroidal pump limiter: experience feedback of HHF elements series manufacture 20th IEEE/NPSS/SOFE (San-Diego, 2003) p 6
7. Boscary J. et al 2004 Applied technologies and inspections for the W7-X pre-series target elements Proc. 23rd SOFT (Venice, 2004) Fusion Eng. Des. submitted
8. Boscary J., Fabre J. and Schlosser J. 1999 Critical heat flux of water subcooled flow in one-side heated swirl tubes Int. J. Heat Mass Transfer 42 287
9. Schlosser J. et al 1998 Thermal hydraulic testing for ITER high heat flux components Proc. 20th Symp. on Fusion Technology (Marseille, 1998) p 137
10. Smid I. et al 1996 Comparison between various thermal hydraulic tube concepts for the ITER divertor Proc. 19th Symp. on Fusion Technology (Lisbon, Portugal, 16-20 September 1996) p 263
11. Escourbiac F. et al 2003 Experimental optimisation of a hypervapotron concept for ITER plasma facing components Fusion Eng. Des. 66-68 301-4
12. Schlosser J. et al 2004 Flat tile armour cooled by hypervapotron tube: a possible technology for ITER Phys. Scr. T 111 199-202
13. Merola M. 2004 EU R&D on divertor components Proc. 23rd SOFT (Venice, 2004) Fusion Eng. Des. submitted
14. Missirlian M. et al 2004 Results and analysis of high heat flux tests on a full scale vertical target prototype of ITER divertor Proc. 23rd SOFT (Venice, 2004) Fusion Eng. Des. submitted
15. Escourbiac F. et al 2001 High heat flux behaviour of damaged plasma facing components Fusion Eng. Des. 56-57 285-90
16. Roedig M. et al 2004 Post irradiation testing of samples from the irradiation experiments PARIDE 3 and PARIDE 4 J. Nucl. Mater. 329-333 766-70
17. Roedig M. et al 2002 High heat flux performance of neutron irradiated plasma facing components J. Nucl. Mater. 307-311 753-9
18. Escourbiac F. et al Experimental simulation of cascade failure effect on tungsten and CFC flat tile armoured high heat flux components in Fusion Eng. Des. submitted
19. Durocher A. et al 2004 Development of an original active thermography method adapted to ITER plasma facing components control Proc. 23rd SOFT (Venice, 2004) Fusion Eng. Des. submitted
20. D'agata E. and Tivey R. 2004 Towards the development of workable acceptance criteria for the divertor CFC monoblock armour Proc. 23rd SOFT (Venice, 2004) Fusion Eng. Des. submitted