Dynamics of initial penetration in drilling: Part 2 - Motion models for drill skidding and wandering with experimental verification

Journal of Manufacturing Science and Engineering

Volumn 127, Issue 2, 2005, Pages 289-297

  Gong, Yongping ^a   Lin, Cheng ^a   Ehmann, Kornel F ^a  

^a Northwestern University   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

BOUNDARY CONDITIONS; CUTTING; DAMPING; FINITE ELEMENT METHOD; MATHEMATICAL MODELS; VIBRATIONS (MECHANICAL);

DRILL SKIDDING; DYNAMIC FORCE; INITIAL PENETRATION DRILLING; VIBRATION ENERGY;

DRILLING;

EID: 19344378702     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1852568     Document Type: Article

References (16)

1. Galloway, D. F., 1957, "Some Experiments on the Influence of Various Factors on Drill Performance," ASME Trans., 79, pp. 191-231.
2. Fujii, H., Marui, E., and Ema, S., 1988, "Whirling Vibration in Drilling. Part 3: Vibration Analysis in Drilling With a Pilot Hole," J. Eng. Ind., 110, pp. 315-321.
3. Fujii, H., Marui, E., and Ema, S., 1986, "Whirling Vibration in Drilling. Part 1: Cause of Vibration and Role of Chisel Edge," J. Eng. Ind., 108, pp. 157-162.
4. Fujii, H., Marui, E., and Ema, S., 1986, "Whirling Vibration in Drilling. Part 2: Influence of Drill Geometries, Particularly of the Drill Flank, on the Initiation of Vibration," J. Eng. Ind., 108, pp. 163-168.
5. Lee, S. J., Eman, K. F., and Wu, S. M., 1987, "An Analysis of the Drill Wandering Motion," J. Eng. Ind., 109, pp. 297-305.
6. Lin, C., Jalisi, M. N., and Ehmann, K. F., 1994, Material Issues in Machining-II, Stephenson, D. A., and Stevenson, R., eds., pp. 383-408, TMS, Warrendale.
7. Tekinalp, O., and Ulsoy, A. G., 1992, "Effects of Geometric and Process Parameters on Drill Transverse Vibrations," I. Eng. Ind., 112, pp. 189-19.
8. Wijeyewickrema, A. C., Keer, L. M., and Ehmann, K. F., 1995, "Drill Wandering Motion: Experiment and Analysis," Int. J. Mech. Sci., 37, pp. 495-509.
9. Bayly, P. V., Young, K. A., Calvert, S. G., and Halley, J. E., 2001, "Analysis of Tool Oscillation and Hole Roundness Error in a Quasi-Static Model of Reaming," J. Manuf. Sci. Eng., 123, pp. 387-396.
10. Bayly, P. V., Metzler, S. A., Schaut, A. J., and Young, K. A., 2001, "Theory of Torsional Chatter in Twist Drills: Model, Stability Analysis and Composition to Test," J. Manuf. Sci. Eng., 123, pp. 552-561.
11. Bayly, P. V., Lamar, M. T., and Calvert, S. G., 2002, "Low-Frequency Regenerative Vibration and the Formation of Lobed Holes in Drilling," J. Manuf. Sci. Eng., 124, pp. 275-285.
12. Kaminski, J., and Crafoord, R., 1994, "Positional Accuracy of Holes When Drilling in Inclined Workpiece Surfaces, Part I-Experimental Results," Proc. Inst. Mech. Eng., 208, pp. 129-139.
13. Kaminski, J., and Crafoord, R., 1994, "Positional Accuracy of Holes When Drilling in Inclined Workpiece Surfaces, Part II-Mathematical Force Model," Proc. Inst. Mech. Eng., 208, pp. 141-152.
14. Gong, Y., and Ehmann, K. F., 2001, "Mechanistic Model for Dynamic Forces in Micro-Drilling," ASME International Mechanical Engineering Congress and Exposition, New York, Nov. 11-16, 2001.
15. Gong, Y. P., 2001, "Modeling and Simulation of Micro-Drilling Dynamics," Ph.D thesis, Northwestern University, Evanston, Illinois.
16. Chandrasekharan, V., Kapoor, S. G., and Devor, R. E., 1997, "A Calibration Procedure for Fundamental Oblique-Cutting Model Coefficients Based on a Three Dimensional Mechanistic Drilling Force Model," Trans. NAMRI/SME, 25, pp. 255-260.