Analysis of the cutting force components and friction in high speed machining

Journal of Manufacturing Science and Engineering

Volumn 127, Issue 2, 2005, Pages 245-250

  Sutter, G ^a   Molinari, A ^a  

^a UNIVERSITÉ DE LORRAINE   (France)

Author keywords

Cutting Forces; Friction; High Speed Machining; Orthogonal Cutting

Indexed keywords

CAMERAS; CUTTING; FRICTION; MACHINE TOOLS; OPTICAL RECORDING; PHOTOGRAPHY;

CUTTING FORCES; HIGH SPEED MACHINING; ORTHOGONAL CUTTING; TANGENTIAL FORCES;

MACHINING;

EID: 19344375071     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1863253     Document Type: Article

References (17)

1. Sutter, G., Molinari, A., Faure, L., Klepaczko, J. R., and Dudzinski, D., 1998, "An Experimental Study of High Speed Orthogonal Cutting," ASME J. Manuf. Sci. Eng., 120, pp. 169-172.
2. Merchant, E., 1945, "Mechanics of the Metal Cutting Process. I. Orthogonal Cutting and a Type 2 Chip," J. Appl. Phys., 16(5), pp. 267-324.
3. Kottenstette, J. P., and Recht, R. F., 1982, "Ultra-High-Speed Machining Experiments," Proceedings, Ninth North American Manufacturing Research Conference, Trans. ASME, pp. 263-270.
4. Hoffmeister, H. W., Gente, A., and Weber, T. H., 1999, "Chip Formation at Titanium Alloys under Cutting Speed of up to 100 m/s," 2nd International Conference on High Speed Machining, edited by Schulz, H., Molinari, A., Dudzinski, D., PTW Darmstadt University, pp. 21-28.
5. Lee, D., 1985, "The Effect of Cutting Speed on Chip Formation under Orthogonal Machining," Int. J. Eng. Industry, 107, pp. 55-63.
6. Hastings, W. F., Mathews, P., and Oxley, P. L. B., 1980, "A Machining Theory For Predicting Chip Geometry, Cutting Forces etc. from Material Properties and Cutting Conditions," Proc. R. Soc. London, Ser. A, 371, pp. 569-587.
7. Komanduri, R., Flom, D. G., and Lee, M., 1984, "High Speed Machining," edited by Komanduri, R., Subramanian, K., and Von Turkovich, B. F., ASME, pp. 15-36.
8. Findley, W. N., and Reed, R. M., 1963, "The Influence of Extreme Speeds and Rake Angles in Metal Cutting," ASME J. Eng. Ind., 85(2), pp. 49-67.
9. Wallace, P. W., and Boothroyd, G., 1964, "Tool Forces and Tool-Chip Friction in Orthogonal Machining," J. Mech. Eng. Sci., 6(1), pp. 74-87.
10. Mathew, P., and Oxley, P. L. B., 1982, "Predicting the Effects of Very High Cutting Speeds on Cutting Forces, etc.," CIRP Ann., 31(1), pp. 49-52.
11. Bredendick F., 1959, Die Massenkräfte beim Zerspanvorgang. Werkstatt und Betrieb, Jahrg. 92, Heft 10, Carl Hanser Verlag, München, pp. 739-742.
12. Klocke, F., Raedt, H.-W., and Hoppe, S., 2001, "2d-FEM simulation of the orthogonal high speed cutting process," Mach. Sci. Technol., 5(3), pp. 323-340.
13. Salomon, C. J., 1931, "Process for the Machining of Metals of Similarly-Acting Materials When Being Worked by Cutting Tools," German Patent No 523594.
14. Recht, R. F., 1984, "A Dynamic Analysis of High Speed Machining," High Speed Machining, edited by Komanduri, R. et al., ASME, New York, pp. 83-93.
15. Sutter, G., Faure, L., Molinari, A., Delime, A., and Dudzinski, D., 1997, "Experimental Analysis of Cutting Process and Chip Formation at High Speed Machining," J. Phys. IV, 7, pp. C3-33 - C3-38.
16. Tanaka, Y., Tsuwa, H., and Kitano, M., 1967, "Cutting Mechanism in Ultra-High-Speed Machining," Trans. ASME, paper No 67-PROD-14.
17. Montgomery, R. S., 1976, "Friction and Wear at High Sliding Speeds," Wear, 36, pp. 275-298.