Influence of entrance geometry on heat transfer in rotating rectangular cooling channels (AR=4:1) with angled ribs

Journal of Heat Transfer

Volumn 127, Issue 4, 2005, Pages 378-387

  Wright, Lesley M ^a   Fu, Wen Lung ^a   Han, Je Chin ^a  

^a Department of Electrical and Computer Engineering   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COOLING; HEAT FLUX; HYDRAULICS; REYNOLDS NUMBER;

COOLING CHANNELS; HEIGHT-TO-HYDRAULIC DIAMETER RATIO; PARTIAL SUDDEN CONTRACTION; RECTANGULAR COOLING CHANNELS;

HEAT TRANSFER;

CHANNEL; COOLING; HEAT TRANSFER;

EID: 18844426823     PISSN: 00221481     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1860564     Document Type: Article

References (17)

1. Han, J. C., Dutta, S., and Ekkad, S. V., 2000, Gas Turbine Heat Transfer and Cooling Technology, Taylor and Francis, New York.
2. Johnson, B. V., Wagner, J. H., Steuber, G. D., and Yeh, F. C., 1994a, "Heat Transfer in Rotating Serpentine Passage With Trips Skewed to the Flow," ASME J. Turbomach., 116, pp. 113-123.
3. Johnson, B. V., Wagner, J. H., Steuber, G. D., and Yeh, F. C., 1994b, "Heat Transfer in Rotating Serpentine Passage With Selected Model Orientations for Smooth or Skewed Trip Walls," ASME J. Turbomach., 116, pp. 738-744.
4. Dutta, S., and Han, J. C., 1996, "Local Heat Transfer in Rotating Smooth and Ribbed Two-Pass Square Channels With Three Channel Orientations," ASME J. Heat Transfer, 118, pp. 578-584.
5. Taslim, M. E., Rahman, A., and Spring, S. D., 1991a, "An Experimental Investigation of Heat Transfer Coefficients in a Span-Wise Rotating Channel With Two Opposite Rib-Roughened Walls," ASME J. Turbomach., 113, pp. 75-82.
6. Taslim, M. E., Bondi, L. A., and Kercher, D. M., 1991b, "An Experimental Investigation of Heat Transfer in an Orthogonally Rotating Channel Roughened With 45° Criss-Cross Ribs on Two Opposite Walls," ASME J. Turbomach., 113, pp. 346-353.
7. Azad, G. S., Uddin, M. J., Han, J. C., Moon, H. K., and Glezer, B., 2002, "Heat Transfer in a Two-Pass Rectangular Rotating Channel With 45° Angled Rib Turbulators," ASME J. Turbomach., 124, pp. 251-259.
8. Al-Qahtani, M., Jang, Y. J., Chen, H. C., and Han, J. C., 2002, "Prediction of Flow and Heat Transfer in Rotating Two-Pass Rectangular Channels With 45° Rib Turbulators, ASME J. Turbomach., 124, pp. 242-250.
9. Griffith, T. S., Al-Hadhrami, L., and Han, J. C., 2002, "Heat Transfer in Rotating Rectangular Channels (AR=4) With Angled Ribs," ASME J. Heat Transfer, 124, pp. 617-625.
10. Lee, E., Wright, L. M., and Han, J. C., 2003, "Heat Transfer in Rotating Rectangular Channels (AR-4: 1) With V-Shaped and Angled Rib Turbulators; With and Without Gaps," ASME Paper No. 2003-GT-38900.
11. Kays, W. M., and Crawford, M. E., 1993, Convective Heat and Mass Transfer, 3rd ed., McGraw-Hill, New York, pp. 345-348.
12. Boelter, L. M. K., Young, G., and Iverson, H. W., 1948, An Investigation on Aircraft Heaters-Distribution of Heat Transfer Rate in the Entrance Section of a Circular Tube," NACA Technical Note No. 1451.
13. Burggraf, F., 1970, "Experimental Heat Transfer and Pressure Drop With Two-Dimensional Turbulence Promoter Applied to Two Opposite Walls of a Square Duct," in Augmentation of Convective Heat and Mass Transfer , edited by A. E. Bergles and R. L. Webb, ASME, New York, pp. 70-79.
14. Han, J. C., and Park, J. S., 1988, "Developing Heat Transfer in Rectangular Channels With Rib Turbulators," Int. J. Heat Mass Transfer, 31, pp. 183-195.
15. Loui, T. M., and Hwang, J. J., 1992, "Developing Heat Transfer and Friction in a Ribbed Rectangular Duct With Flow Separation at Inlet," ASME J. Heat Transfer, 114, pp. 565-573.
16. Park, J. S., Han, J. C., Huang, Y., and Ou, S., 1991, "Heat Transfer Performance Comparisons of Five Different Rectangular Channels With Parallel Angled Ribs," Int. J. Heat Mass Transfer, 35, pp. 2891-2902.
17. Kline, S. J., and McClintock, F. A., 1953, "Describing Uncertainties in Single-Sample Experiments," Mech. Eng. (Am. Soc. Mech. Eng.), 75, pp. 3-8.