Three-dimensional simulation of plasma spray jet

Proceedings of the ASME Summer Heat Transfer Conference

Volumn 2003, Issue , 2003, Pages 689-697

  Xiong, H ^a   Zheng, L L ^a   Sampath, S ^a   Fincke, Jim ^b   Williamson, Richard ^b  

^a Stony Brook University   (United States)

^b U S ARMY ENGINEER RESEARCH AND DEVELOPMENT CENTER   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CERAMIC COATINGS; COMPRESSIBLE FLOW; COMPUTATIONAL FLUID DYNAMICS; COMPUTER SIMULATION; CORROSION RESISTANCE; NOZZLES; OPTIMIZATION; PARTICLE BEAM INJECTION; PLASMA SPRAYING; TURBULENT FLOW; WEAR RESISTANCE;

CARRIER GASES; THERMO-FLUID FLOWS;

PLASMA JETS;

EID: 1842740958     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1115/ht2003-47153     Document Type: Conference Paper

References (13)

1. Ahmed, I., and Bergman, T.L., "Simulation, of thermal plasma spraying of partially molten ceramics: effect of carrier gas on particle deposition and phase change phenomena", Transaction of the ASME, Vol.123, pp.188-196 (2001).
2. Chang, C. H. and Pfender, E., "Non-equilibrium modeling of low-pressure argon plasma jets: Part II: turbulent flow," Plasma Chemistry and Plasma Processing, Vol.10, p.493 (1990).
3. Chang, C.H. and Ramshaw, J.D., "Numerical simulations of Argon plasma jets flowing into cold air," Plasma Chemistry and Plasma Processing, Vol.13, pp.189-209 (1993).
4. Chen, X. and Pfender, E., "Behavior of small particles in a thermal plasma flow," Plasma chemistry and plasma processing, Vol. 3, No. 3, pp.351-366 (1983).
5. Fincke, J.R., Swank, W.D. and Haggard, D.C., "The influence of injector geometry and carrier gas flow rate on spray pattern", Thermal Spray: A United Forum for Scientific and Technological Advances, Proceedings of the National Thermal Spray Conference, USA, (ed.) C.C. Berndt, (pub.) ASM Int. OH, USA, pp.335-342, 1997.
6. Lee, Y. C., "Modeling work in thermal spraying processing," PhD thesis, University of Minnesota, 1984.
7. Li, H.-P. and Chen, X., "Three-dimensional simulation of a plasma jet with transverse particle and carrier gas injection," Thin Solid Films, Vol. 390, pp. 175-180 (2001).
8. Li, H.-P. and Chen, X., "Three-dimensional simulation of the turbulent plasma jet impinging upon a flat plate and with transverse particle and carrier gas injection", Plasma Chemistry and Plasma Process, Vol. 22, pp.27-57 (2002).
9. Ramshaw, J.D. and Chang, C.H., "Computational fluid dynamics modeling of multicomponent thermal plasmas," Plasma Chemistry and Plasma Processing, Vol. 12, pp. 299-325 (1992).
10. Scott, D.A, Kovitya, P. and Haddad, G. N., "Temperatures in the plume of a DC plasma torch," Journal Applied Physics, Vol. 66, p.5232, 1989.
11. Vardelle, M., A. Vardelle, P., Fauchais, K.-I. Li, B. Dussoubs, and N.J. Thermelis, "Controlling particle injection in plasma spraying," Journal of Thermal Spray Technology, Vol. 10 pp.267-284 (2001).
12. Wan, Y. P., Fincke, J. R., Sampath, S., Prasad, V., Herman, H., "Modeling and experimental observation of evaporation from oxidizing molybdenum particles entrained in a thermal plasma jet," International Journal of Heat and Mass Transfer, 45 (2002) 1001-10015.
13. Wang, G.-X., and Matthys, E. F., "Modeling of nonequilibrium surface melting and resolidification for pure metals and binary alloys," Transaction of ASME, Heat Transfer Division, Vol. 118, pp.944-951 (1996).