Tool path planning using trochoid cycles for hardened steel in die and mold manufacturing (1st report) - Tool path generation for trochoid cycles based on voronoi diagram -

Proceedings of the International Conference on Agile Manufacturing, Advances in Agile Manufacturing, ICAM 2003

Volumn , Issue , 2003, Pages 435-442

  Ibaraki, Soichi ^a   Yamaji, Iwao ^a   Kakino, Yoshiaki ^a   Inoue, Daisuke ^b   Nishida, Susumu ^c  

^a KYOTO UNIVERSITY   (Japan)

^b KUBOTA CORPORATION   (Japan)

^c Graphic Products   (Japan)

Author keywords

Contour parallel paths; Die and mold manufacturing; End mill; Tool path planning; Trochoid cycles; Voronoi diagram

Indexed keywords

ALGORITHMS; CUTTING TOOLS; DIES; HARDENING; IRON AND STEEL PLANTS; MOLDING; PLANNING; PROCESS ENGINEERING; PRODUCTIVITY; STEELMAKING;

CONTOUR PARALLEL PATHS; DIE AND MOLD MANUFACTURING; END MILL; HARDENED STEEL; ROUGH CUTTING; TOOL PATH PLANNING; TROCHOID CYCLES; VORONOI DIAGRAM;

COMPUTER INTEGRATED MANUFACTURING;

EID: 1842610772     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (19)

1. Schramm, A. 2000. Study on an Intelligent CAM-System for Die and Mold Making (ICAMS). Ph.D. Thesis. Kyoto University.
2. Iwabe, H., Fujii, Y., Saito, K. & Kishinami, T. 1994. Study on corner cut by end mill, Int. J. of JSPE, 28(8).
3. Li, Y., Iwabe, H. & Fujii, Y. 1992. Study on improvement of machining accuracy in cornering cut with end mill, JSME Int. J. Series III, 35(1).
4. Yamaji, I., Ibaraki, S., Kakino, Y. & Nishida, S. 2003. Tool path planning using trochoid cycles for hardened steel in die and mold manufacturing (2nd report)-Tool path planning to avoid an excessive tool load-, To be presented at ICAM2003.
5. Dragomatz, D. & Mann, S. 1997. A classified bibliography of literature of NC milling path generation. Computer-Aided Design. 29(3): 239-247.
6. Landers, R. G., Ulsoy, A. G. 2000. Model-based Machining Force Control, ASME J. of Dynamic Systems, Measurement, and Control, 122(3): 521-527.
7. Kakino, Y., Ohtsuka, H., Nakagawa, H., and Hirogaki, T. 2000. NC Programming for Constant Cutting Force in Die Machining, Proc. of 2000 Int'l Conf. on Advanced Manufacturing Systems and Manufacturing Automation, 471-475.
8. Ibaraki, S., Ogawa, T., Matsubara, A., and Kakino, Y. 2002. Model-based Learning Control of Cutting Forces in End Milling Processes, Proc. of 2002 Japan-USA Symposium on Flexible Automation, 1: 401-408.
9. http://www.graphicproducts.co.jp
10. Yamaji, I., Kakino, Y., Ibaraki, S., Otsuka, H., Saraie, H., Nakagawa, H., 2002. Influence of Die Geometry on Tool Life in Endmilling of Hardened Steel, Progress of Machining Technology (Proc. of 6th ICPMT), 122-127.
11. Adachi, Y. 2003. The effect of cutting heat on the tool life in die and mold manufacturing, Master Thesis. Kyoto University (in Japanese).
12. Iwabe, H., Fujii, Y., Saito, K., and Kishinami, T. 1989. Study on Corner Cut by End Mill-Analysis of Cutting Mechanism and New Cutting Method of Inside Corner. Journal of JSPE, 55(5): 841-846 (in Japanese).
13. http://www.mastercam.com/
14. Stori, J. A. and Wright, P. K. 2000. Constant Engagement Tool-Path Generation for Convex Geometries, J. of Manufacturing Systems, 19(3): 172-184.
15. Persson, H. 1978. NC machining of arbitrarily shaped pockets, Computer Aided Design, 10(3): 169-174.
16. Held, M. 2001. VRONI: An Engineering Approach to the Reliable and Efficient Computation of Voronoi Diagrams of Points and Line Segments. Computational Geometry: Theory and Application, 18(2): 95-123.
17. Held, M. 1991. On the computational geometry of pocket machining, Lecture Notes in Computer Science vol.500, Springer.
18. http://www.cosy.sbg.ac.at/~held/projects/vroni/vroni.html
19. Choi, W. & Inui, M. 2001. A fast algorithm to generate pocketing paths using graphics hardware. Proc. of 2001 Fall JSPE semiannual meeting. 155 (in Japanese).