A study of tribological behaviour of polyamide 66 with varying injection-moulding parameters

Wear

Volumn 250-251, Issue PART 2, 2001, Pages 1557-1566

  Apichartpattanasiri, S ^a   Hay, J N ^a   Kukureka, S N ^a  

^a UNIVERSITY OF BIRMINGHAM   (United Kingdom)

Author keywords

Optical microscopy; Polyamide 66; Tribological behaviour

Indexed keywords

DIFFERENTIAL SCANNING CALORIMETRY; GEARS; INJECTION MOLDING; MICROSTRUCTURE; OPTICAL MICROSCOPY; SURFACE STRUCTURE; TRIBOLOGY; WEAR OF MATERIALS;

BEARING APPLICATIONS;

POLYAMIDES;

MICROSCOPY; POLYAMIDE; TRIBOLOGY; WEAR RESISTANCE;

EID: 18144438430     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/s0043-1648(01)00794-3     Document Type: Article

References (37)

1. Structure and properties of injection-moulded nylon-6. Part 1. Structure and morphology of nylon-6'
2. Structure and properties of injection-moulded nylon-6. Part 2. Residual stresses in injection-moulded nylon-6'
3. Structure and properties of injection-moulded nylon-6. Part 3. Yield and fracture of injection-moulded nylon-6'
4. Structural analysis of injection-moulded semi-crystalline polymers by fourier transform infra-red spectroscopy with photoacoustic detection and differential scanning calorimetry. 1. Poly(ethylene terephthalate)
5. Structural analysis of injection-moulded semi-crystalline polymers by Fourier transform infra-red spectroscopy with photoacoustic detection and differential scanning calorimetry. 1. Polyamide-6,6'
6. Effect of water absorption on residual stresses in injection-moulded nylon-6,6'
7. Distortion of nylon-6,6' mouldings caused by asymmetric water absorption
8. Morphology of nylon-6 spherulites in bulk
9. The effect of skin-core morphology on the impact fracture of poly(butylene terephthalate)
10. Accurate measurement of creep of nylon-6,6' at constant temperature and humidity
11. The influence of temperature and absorbed water on the fatigue crack propagation in nylon-6,6'
12. The effect of crystallinity on the properties of injection-moulded polypropylene and polyacetal
13. Effect of injection-moulding conditions on the crystallinity, orientation gradients, and mechanical properties of poly(aryl ether ketone). Part II. Large dumbbell parts
14. Studies of microstructural and mechanical properties of nylon/glass composite. Part I. The effect of thermal processing on crystallinity, transcrystallinity and crystal phases
15. Studies of microstructural and mechanical properties of nylon/glass composite. Part II. The effect of microstructures on mechanical and interfacial properties
16. Friction and wear mechanisms of a thermoplastic composite GF/PA6 subjected to different thermal histories
17. Dry sliding wear behaviour of polyamide 66 and polycarbonate composites
18. Tribological studies of glass fabric-reinforced polyamide composites filled with CuO and PTFE
19. Studies on abrasive wear of carbon fibre (short) reinforced polyamide composites
20. Wear behaviour of acetal gear pairs
21. The friction and wear of polymers in non-conformal contacts
22. Wear testing and measurement techniques for polymer composite gears
23. Friction and wear behaviour of 18 polymers in contact with steel in environments of air and water
24. Rolling contact wear of polymers: A preliminary study
25. Crystallization phenomena in the injection-molding of polyether-ether-ketone and its influence on mechanical properties
26. The microstructure of injection-moulded thermotropic copolyester. Part 1. Optical and scanning electron microscopy studies
27. The wear mechanisms of acetal in unlubricated rolling-sliding contact
28. The effect of fibre reinforcement on the friction and wear of polyamide 66 under dry rolling-sliding contact
29. Thermal degradation of nylon polymers
30. Physical structure of nylons