High temperature sliding abrasion of a nickel-base alloy and composite

Wear

Volumn 225-229, Issue I, 1999, Pages 154-162

  Berns, Hans ^a   Koch, Stefan ^a  

^a RUHR UNIVERSITY BOCHUM   (Germany)

Author keywords

Composite; High temperature; Nickel base alloy; Oxidation; Protective layer; Sliding abrasion

Indexed keywords

ABRASION; AIR; ARGON; CORUNDUM; HARDNESS; NICKEL ALLOYS; OXIDATION; OXIDATION RESISTANCE; PROTECTIVE COATINGS; SILICON CARBIDE; TUNGSTEN CARBIDE; WEAR RESISTANCE;

SLIDING ABRASION;

METALLIC MATRIX COMPOSITES;

ABRASION; COMPOSITE; NICKEL ALLOY; SLIDING; WEAR;

EID: 18144433727     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0043-1648(99)00008-3     Document Type: Article

References (16)

1. H. Berns, A. Fischer, Tribological stability of metallic materials at elevated temperatures, Wear 162-164 (1993) 441-449.
2. H. Berns, Microstructural properties of wear-resistant alloys, Wear 181-183 (1995) 271-279.
3. H. Berns, S.D. Franco, Effect of coarse hard particles in high temperature sliding abrasion of new metal matrix composites, Wear 203-204 (1997) 606-614.
4. H.-J. Boosz, The resistance of hard particles to gases (in German), Metall. 10 (3/4) (1956) 130-136.
5. H. Berns, A. Fischer, W. Theisen, Microstructure of Ni-Cr-B-Si hardfacing alloys with additions of Al, Nb, Mo, Fe and C, Proc. 22nd Annual convention, Intern., Metallographic Society, Charlotte, NC, USA, July 1989.
6. M. Lührig, Temperature dependence of microhardness of phases in alloys (in German), Dr.-Ing. thesis Ruhr-University Bochum, Fortschr.-Ber., VDI-Reihe 5, No. 297, VDI-Verlag, Düsseldorf, 1993.
7. K.M. Liang, G. Orange, G. Fantozzi, Evaluation by indentation of fracture toughness of ceramic materials, J. Mat. Sci. 25 (1990) 213-297.
8. J. Keff, Hot scratching of metallic materials (in German), Dr.-Ing. thesis Ruhr-University Bochum, Fortschr.-Ber., VDI-Reihe 5, Nr. 340, VDI-Verlag, Düsseldorf, 1994.
9. 2 (in German), Schweißen und Schneiden 45 (8) (1993) 494-498.
10. C.C. Koch, Mechanical milling and alloying, in: R.W. Cahn (Ed.), Materials Science and Technology, Vol. 15, VCH Verlagsgesellschaft, Weinheim, 1991.
11. H. Berns, N. van Chuong, A new microstructure for PM Tooling Material, Met. Phys. Adv. Tech. 16 (1996) 693-706.
12. A. Pyzalla, Residual microstresses in microstructures, in: H. Berns (Ed.), Hard alloys and hard composites (in German), Springer-Verlag, Berlin, 1998.
13. D.F. Watt, X.Q. Xu, D.J. Lloyd, Effects of particle morphology and spacing on the strain fields in a plastically deforming matrix, Acta Mater. 44 (2) (1996) 789-799.
14. K.L. Johnson, K. Kendall, A.D. Roberts, Surface energy and the contact of elastic solids, Proc. R. Soc. London A 324 (1971) 301-313.
15. H. Berns, S. Koch, Influence of abrasives on wear mechanism and wear resistance in a sliding abrasion test at elevated temperatures, special issue of Wear, Intern. Conference on Erosive and Abrasive Wear, Cambridge, England, Sept. 1998.
16. J. Jang, F.H. Stott, M.M. Stack, The effect of partial pressure of oxygene on the tribological behaviour of a nickel-based alloy, N80A, at elevated temperatures, Wear 203-204 (1997) 615-625.