Method for generation of rheological model to characterize non-conventional injection molding by means of spiral mold

Journal of Materials Processing Technology

Volumn 162-163, Issue SPEC. ISS., 2005, Pages 477-483

  Claveria I ^a   Javierre, C ^a   Ponz, L ^a  

^a UNIVERSITY OF ZARAGOZA   (Spain)

Author keywords

Injection; Model; Mold; Recycled; Rheological; Spiral

Indexed keywords

CAPILLARITY; CHARACTERIZATION; COMPUTER SIMULATION; MARKETING; RECYCLING; RHEOLOGY; RHEOMETERS; TECHNOLOGY TRANSFER; FUNGI; INJECTION (OIL WELLS); MATERIALS; MODELS; MOLDS;

INJECTION; PRESSURE SENSORS; RECYLED; SPIRAL MOLD;

INJECTION MOLDING;

CAPILLARY RHEOMETER; CONVENTIONAL INJECTION MOLDING; MATERIAL PROCESSING; PROCESSING TECHNOLOGIES; RECYCLED; RHEOLOGICAL; RHEOLOGICAL CHARACTERIZATION; SPIRAL;

EID: 17844383500     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2005.02.065     Document Type: Conference Paper

References (25)

1. K.B. Abbas Degradation of polycarbonate during recycling in a capillary rheometer Polym. Eng. Sci. 10 1980 703 707
2. A. Albertsson, and S.J. Huang Degradable Polymers, Recycling and Plastics Waste Management, Proceedings 1995 Marcel Dekker Incorporated
3. O. Amano, and K. Ainoya Pressure dependent viscosity of polymer melts Antec'00 Conference Proceedings 2000 89
4. W.F. Ames Numerical Methods for Partial Differential Equations 2nd ed. 1977 Academic Press New York
5. H.A. Barnes, J.F. Hutton, and K. Walters An Introduction to Rheology 1989 Elsevier Science Publishers B.V. Amsterdam
6. M.L. Berins Plastics Engineering Handbook of the Society of the Plastics Industry 5th ed. 1991 Van Nostrand Reinhold New York
7. J. Brandrup, M. Bittner, and W. Michaeli Recycling and Recovery of Plastics 1996 Hanser-Hanser/Gardner
8. C.T. Burke, and D.O. Kazmer Experimental comparison of state of the art high shear rate polymer rheological characterization techniques Antec'94 Conference Proceedings I 1994 572 580
9. N. Dontula, G.A. Campbell, and J.J. Wenskus Approach towards moulding parts with constant properties on addition of regrind Antec'94 Conference Proceedings II 1994 1783 1787
10. D.-M. Fann, P.-K. Chang, R.-Y. Hsieh, S.K. Huang, and J.-Y. Lee Flow characteristics of recycled low density and linear low density polyethylene Antec'98 Conference Proceedings III 1998 3487 3491
11. S.I. Gucerin C.L. Tucker Finite Difference Solution of Field Problems in Computer Modeling for Polymer Processing 1989 Hanser Publishers
12. A. Haghtalab, M. Hemmati, and J. Alaie Rheological study of polyethylene/polypropylene blends Iran. J. Polym. Sci. Technol. 4 2000 11 16
13. S. Hettinga Controlled low-pressure injection moulding Stevenson Innovation in Polymer Processing Molding 1996 Hanser Publishers Munich
14. D.A. Hoffman Effect of recycled phenolics on processing Antec'94 Conference Proceedings 1 1994 883
15. C.C. Lee, and J.M. Castro L. Tucker III Model Simplification in Fundamentals of Computer Modelling for Polymer Processing 1989 Hanser Publishers Munich
16. M. Menges How to Make Injection Moulds? 2nd ed. 1993 Hanser Publishers Munich
17. D. Nichetti, and I. Manas-Zloczower Viscosity model for polydisperse polymer melts J. Rheol. 4 1998 951 969
18. K. Peter Flow Análisis of Injection Molds 1995 Hanser Publishers Munich
19. A. Pillo, J.M. Dealy, and W.I. Patterson Upgrading recycled HDPE by rheometer controlled crosslinking Int. Polym. Process. 1 1997 4 10
20. N.S. Rao Design Formulas for Plastics Engineers 1991 Hanser Publishers Munich
21. E.E. Rosenbaum, and S.G. Hatzikiriatos Effect of viscous heating in capillary rheometry Antec'94 Conference Proceedings I 1996 1080 1084
22. J. Rothe Special injection moulding methods Kunstoffe 87 1997 1564 1581
23. Scheirs Polymer Recycling: Science, Technology and Applications 1998 John Wiley and Sons Canada Ltd.
24. T. Scriven, and S. Sykes Analysis of pre-consumer regrind in an injection moulded thermoplastic part Antec'95 Conference Proceedings I 1995 348 350
25. C.L. Tucker Computer Modeling for Polymer Processing 1989 Hanser Publishers