Overspray injection in spray forming of CuSn13.5 billets

Materials Science and Engineering: A

Volumn 383, Issue 1 SPEC. ISS., 2004, Pages 114-121

  Schneider, Alexander ^a   Uhlenwinkel, Volker ^a   Harig, Helmuth ^a   Bauckhage, Klaus ^a  

^a UNIVERSITY OF BREMEN   (Germany)

Author keywords

Billet; Overspray; Particle injection; Spray forming; Yield

Indexed keywords

ATOMIZATION; DEPOSITION; FLOW MEASUREMENT; MICROSTRUCTURE; POROSITY; POWDERS;

GAS CONSUMPTION; MELT MASS FLOW RATE (MMFR); SIEVING; SPRAY CONES;

FORMING;

SPRAYING;

EID: 17344364999     PISSN: 09215093     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.msea.2004.02.038     Document Type: Article

References (17)

1. E. Lavernia, Y. Wu, Spray Atomization and Deposition, John Wiley & Sons, 1996.
2. Lawley, A. Proceedings of International Conference on Spray Deposition and Melt Atomization - SDMA, Bremen, 2000, p. 3.
3. Grant P. Prog. Mater. Sci. 39 1995 497
4. K. Hummert, Spray Forming - Kolloquium des SFB 372, vol. 1, University of Bremen, 1996, p. 199.
5. K. Schimanski, A. Schulz, et al., Spray Forming - Kolloquium des SFB 372, vol. 5, University of Bremen, 2001, p. 193.
6. C. Kramer, Die Kompaktierungsrate beim Sprühkompaktieren von Gaußförmigen Depsotis, Ph.D. Thesis, University of Bremen, 1997.
7. M. Buchholz, Untersuchung des Kompaktierverhaltens an sprühkompaktierten Bolzen, Ph.D. Thesis, University of Bremen, 2002.
8. A. Schneider, O. Meyer, et al., Spray Forming - Kolloquium des SFB 372, vol. 5, University of Bremen, 2001, p. 155.
9. Meyer O. Schneider A. et al. Convective heat transfer from a billet due to an oblique impinging circular jet within the spray forming process Int. J. Thermal Sci. 42 6 2003 561
10. V. Uhlenwinkel, A. Schneider, et al., Effect of Particle Injection during Spray Forming of Cu-Sn Billets, PM2TEC, Orlando, 2002.
11. A. Schneider, R. Klein, V. Uhlenwinkel, H. Henein, Investigation of Local Particle Mass Flux in a Jet Stream with an Isokinetic Probe Symposium Spray Forming SFB 372, vol. 6, University of Bremen, 2002, p. 111.
12. H. Müller, S. Hansmann, K. Ohla, Proceedings of the International Conference on Spray Deposition and Melt Atomization - SDMA, Bremen, 2000, p. 205.
13. K. Ohla, H. Müller, M. Keppeler, Spray Forming of CuSn13-17, PM2TEC, New Orleans, 2001.
14. A. Schneider, V. Uhlenwinkel, K. Bauckhage, Spray Forming - Kolloquium des SFB 372, vol. 5, University of Bremen, 2001, p. 69.
15. A. Schneider, V. Uhlenwinkel, et al., Proceedings of the International Conference on Spray Deposition and Melt Atomization - SDMA, Bremen, 2000, p. 219.
16. 2Si Billets with Graphite, PM2TEC, New Orleans, 2001.
17. Mingard K. Cantor B. Palmer I. et al. Acta Mater. 48 2000 2435