Two-phase upward flow 90° bend pressure loss model

Forschung im Ingenieurwesen/Engineering Research

Volumn 69, Issue 2, 2005, Pages 120-130

  Azzi, A ^a   Friedel, L ^b  

^a UNIVERSITY OF SCIENCES AND TECHNOLOGY HOUARI BOUMEDIENE   (Algeria)

^b HAMBURG UNIVERSITY OF TECHNOLOGY   (Germany)

Author keywords

[No Author keywords available]

Indexed keywords

BEND ANGLE; FLOW MULTIPLIERS; GRAVITATIONAL ACCELERATION; PRESSURE LOSS;

ADHESION; EXTRAPOLATION; MATHEMATICAL MODELS; PIPE; PRESSURE EFFECTS; VISCOSITY;

TWO PHASE FLOW;

EID: 16244379266     PISSN: 00157899     EISSN: None     Source Type: Journal    
DOI: 10.1007/s10010-004-0147-6     Document Type: Article

References (41)

1. Ito H (1987) Flow in curved pipes. JSME Intern. J. 30 (262)
2. Gardner GC, Neller PH (1969) Phase distribution in flow of an air/water mixture round bends and past obstructions at the wall of 76 mm bore tube. Proc. Inst. Mech. Engrs 184, 36
3. Maddock C, Lacey PMC, Patrick MA (1974) The structure of two-phase flow in a curved pipe. IChemE Symp. Series No. 38
4. Azzopardi BJ, Sudlow CA (1993) The effect of pipe fittings on the structure of two-phase flow. Proc. UIT Conf., Milano
5. Dean WR (1927) Note on the motion of fluid in a curved pipe. Phil. Mag. 7(4), 208-223
6. Crane Technical Paper 410 (1957) Flow of fluids through valves, fittings and pipe
7. Beij KH (1938) Pressures losses for fluid flow in 90° bends. Research Paper 1110, J. Research National Bureau of Standards 21, 1-18
8. Pigott RJS (1957) Losses in pipe and fittings.Trans ASME 79, 1767-1783
9. Kittredge CP, Rowley DS (1957) Resistance coefficients for laminar and turbulent flow through one-half-inch valves and fittings. Trans ASME 79, 1759-1766
10. Ito H (1959) Friction factors for turbulent flow in curved pipes. Trans Series D, J. Basic Engng 81, 123-134
11. Ito H (1960) Pressure losses in smooth pipe bends.Trans Series D, J. Basic Engng 82, 131-143
12. Mori Y, Nakayama W (1965) Study on forced convective heat transfer in curved pipes. (1st Report, Laminar Region) Int. J. Heat Mass Transfer 8, 67-82
13. Mon Y, Nakayama W (1967) Study on forced convective heat transfer in curved pipes. (2nd Report, Turbulent Region) Int. J. Heat Mass Transfer 10, 37-59
14. Miller DS (1978) Internal flow systems. BHRA Fluid Engineering
15. Robertson JG (1979) Pressure loss coefficient for 90° circular bends. HTFS RS 270
16. Hooper WB (1981) The two-K method predicts head losses in pipe fittings. Chem. Eng. 88, 96-100
17. Edwards MF, Jadallah MSM, Smith R (1985) Head losses in pipe fittings at low Reynolds numbers. Chem. Eng. Res. Des. 63,43-50
18. Idel'chik IE (1989) Flow resistance. A design guide for engineers. Hemisphere
19. Apthorp DM, Medes JS (1981) Calculation of pressure drop in pipe bends. HTFS RS 376
20. Henry JR (1979) Pressure drop during two-phase flow through a 90° horizontal bend. HTFS RS 271
21. Sekoguchi K, Sato Y, Karayasaki A (1968) The influence of mixers, bends and exit section on horizontal two-phase flow.Proc. Int. Symp. Research Cocurrent Gas Liquid Flow. Ontario, Canada, Vol. 1
22. Nørstebo A (1986) Pressure drop in pipe components in two-phase gas-liquid flow. PhD Thesis NTH Trondheim
23. Sookprasong P (1980) Two-phase flow in piping components. MSc Thesis University of Tulsa
24. Fitzsimmons DE (1964) Two-phase pressure drop in piping components. Report Hanford Laboratories HW-80970, Rev. 1
25. Grant IDR, Cotchin CD (1986) Pressure drop measurements for two-phase flow in a 90° horizontal pipe bend. HTFS RS 645
26. Grant IDR, Cotchin CD, White E (1988) Pressure drop measurements for two-phase flow in a series of 90° horizontal pipe bends. HTFS RS 769
27. Grant IDR, Cotchin CD (1989) Measurements of two-phase pressure change in a series of 90° vertical pipe bends, in a pipe contraction and in a pipe expansion. HTFS RS 788
28. Chakrabarti P (1976) Some aspects of annular two-phase flow in a horizontal tube. PhD Thesis Imperial College, London
29. Azzi A, Friedel L, Belaadi S (2000) Two-phase gas/liquid flow pressure loss in bends. Forsch. Ingenieurwes. 65 (10),309-318
30. Chisholm D (1983) Two-phase flow in pipelines and heat exchangers, G. Godwin
31. Deobald TL (1962) An experimental investigation of two-phase pressure losses in pipe elbows. MSc Thesis University of Idaho
32. Usui K, Aoki S, Inoue A (1980) Flow behaviour and pressure drop of two-phase flow through C-shaped bend in vertical plane,(I) Upward flow. J. Nucl. Sci. Technol. 17 (12), 875-887
33. Diener R, Friedel L (1998) Reproductive accuracy of selected void fraction correlations for horizontal and vertical upflow. Forsch. Ingenieurwesen 64 (4/5), 87-97
34. Smith SL (1969) Void fraction in two-phase flow: A correlation based upon an equal velocity head model. Proc. IMechE 184(36), 647-657
35. Rouhani SZ (1974) Modified correlations for void and two-phase pressure drop. AE-RTV-841
36. Azzi A (2001) Analyse des pertes de pression diphasiques (air-eau) dans un coude vertical à 90° en écoulements ascendants. PhD Thesis U.S.T.H.B., Alger
37. Ralston A, Rabinowitz P (1978) A first course in numerical analysis. Me Graw Hill
38. Friedel L (1981) Kriterien für die Beurteilung der Vorhersagegenauigkeit von halb-empirischen Berechnungsmodellen.Chem.-Ing.-Tech. 53 (1), 59
39. Govan AH (1988) A note on statistical methods for comparing measured and calculated values. HTFS RS 767(1), 315-323
40. Schmidt J (1993) Berechnung und Messung der Druckänderungen über plötzliche scharfkantige Rohrerweiterungen und-verengungen bei Gas/Dampf-Flüssigkeitsströmung, Fortschritt-Berichte VDI Reihe 3, Nr. 236
41. Churchill SW (1977) Friction equation spans all fluid flow regimes. Chemical Engng 84 (24), 91-92