MECHANISTIC FORCE MODELS FOR CHIP CONTROL TOOLS

ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE)

Volumn 1997-W, Issue , 1997, Pages 269-276

  Zhu, Rixin ^a   Athavale, Shounak M ^b   Kapoor, Shiv G ^a   DeVor, Richard E ^a  

^a United States of America   (United States)

^b FORD RESEARCH LABORATORY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CUTTING; GAS TURBINES;

CHIP CONTROL; CONTROL TOOLS; FORCE MODELING; GROOVED TOOLS; MACHINING FORCE; MECHANISTIC MODELS; MECHANISTICS; MODELING APPROACH; SPECIFIC CUTTING ENERGY; TOOL GEOMETRY;

CUTTING TOOLS;

EID: 1542742233     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1115/IMECE1997-1162     Document Type: Conference Paper

References (24)

1. Athavale, S. M., 1994, “A Damage-based Model for Predicting Chip Breakability for Obstruction and Groove Tools,” Ph. D. Thesis, N. C. State Univ., Raleigh, USA.
2. Chao, B. T., and Trigger, K. J., 1959, “Controlled Contact Cutting Tools,” Tran.saolion.'! of the ASME, Vol. 81, pp. 139-151.
3. Devon R. E., Chang, T. H. and Sutherland, J. W., 1992, Slolidicul Quality Design and Control, Macmillan (now Prentice-Hall).
4. Endres, W. J., Devor, R. E. and Kapoor, S. G., 1995, “A Dual-Mechanism Approach to the Prediction of Machining Forces: Part I and 2,” ASME Journal ofEngineeringfor Industry, Vol. 117, pp. 526-541.
5. Fu, H. J., Devor, R. E. and Kapoor, S. G., 1984, "A Mechanistic Model for the Prediction of the Force System in Face Milling Operations,” ASME Journal ofEngineering for Industry, Vol. 106, pp. 81-88.
6. Jawahir, 1. S.. 1988, “The Tool Restricted Contact Effect a.s a Major Influencing Factor in Chip Breaking: An Experimental Analysis,” Annals of CIRP, Vol. 37/1, pp. 121.
7. Jawahir, I. S. and Van Luttervelt, C. A, 1993, “Recent Developments in Chip Control Research and Applications,” Annals tifthe CIRP, 42(2).
8. Jawahir, 1. S. and Fang X. D., 1995a, “A Knowledge-Based Approach for Designing Effective Grooved Chip Breakers - 2D and 3D Chip Flow, Chip Curl and Chip Breaking,” Int. J. Adv. Manuf Technol., 10, pp. 225-239.
9. Jawahir. 1. S. and Zhang J. P., 1995b, “An Analysis of Chip Curl Development, Chip Deformation And Chip Breaking in Orthogonal Machining," Trans. ofNAMRl/SME. Vol. XXIII, pp. 109-114.
10. Kline, W. A. and Devor, R. E., 1983, “The Effect of Runout on Cutting Geometry and Force.s in End Milling,” Int. J. MTDR, 23(2/3), pp. 123-140.
11. Loladze, T. N., 1982, Prochnost / Itnosotojkost rechzu.shego inlruinenta (Moscow, Mashinostroenie).
12. Nedess, C. and Hintze, W., 1989, “Characteristic Parameters of Chip Control in Turning Operations with Indexable Insert.s and Three-dimensionally Shaped Chip Formers,” Annals ofthe CIRP, Vol. 38/1, pp. 74-79.
13. Rubenstein, C., 1968, “The Mechanism of Orthogonal Cutting with Controlled Contact Tools,” Int. J. Mach. Tool Des. Res., Vol. 8, pp. 203-216.
14. Rubenstein, C., Venuvinod, P. K. and Lau, W. S., 1986, “Analysi.s of Oblique Cutting with Controlled Contact Tools,” Annals ofthe CIRP, 35(1), pp. 51-54.
15. Sata, T., 1963, “Recent Development Concerning Cutting Mechanics”, Proc. Int. Prod. Engng Res. Conf., Pittsburgh, pp. 18-25.
16. Shi. T. and Ramalingam, S., 1991, “Slip-line Solution for Orthogonal Cutting with a Chip-breaker and Rank Wear,” Int. J. Meeh. Sci., 33(9), pp. 689-704.
17. Shi, T. and Ramalingam, S., 1993, “Modeling Chip Formation with Grooved Tools,” Int. J. Meeh. Sci., Vol. 35(9), pp. 741-756.
18. Strenkowski, J. S., and Athavale, S. M., 1997, “A Partially Constrained Eulerian Orthogonal Cutting Model for Chip Control Tools”, to be published in November 1997 issue of the Journal of Manufacturing Science and Engineering.
19. Waldorf, D. J., 1996, “Shearing, Ploughing, And Wear in Orthogonal Machining,” Ph D. Thesis, University of Illinois at Urbana-Champaign, Urbana, IL.
20. Worthington, B. and Redford, A. H., 1973, “Chip Curl and the Action of the Groove Type Chip Former,” Int. J. MTDR, 13, pp. 257-270.
21. Yang, J. A, 1992, “A Predictive Model of Chip Breaking for Groove-type Tools in Orthogonal Machining of AISI 1020 Steel,” Ph D. Thesis, North Carolina State University, Raleigh, NC.
22. Zhang, B. and Bagchi, A., 1994, “Finite Element Simulations of Chip Formation and Comparison with Machining Experiment,” ASME Journal of Engineering for Industry, Vol. 116, pp. 289-297.
23. Zhu, R., 1997, “Mechanistic Force Model for Grooved Tools in Orthogonal Machining," M.S. Thesis, University of Illinois at Urbana-Champaign, Urbana, IL
24. Zorev, N. N.. 1963, “Interrelation Between Shear Processe.s Occurring Along Tool Face and on Shear Plane in Metal Cutting,” Priic. Ini. Prod. En^n^ Pes. Conf., Pittsburgh, pp. 42-49.