Stability analysis of a rough journal bearing considering cavitation effects

Journal of Tribology

Volumn 127, Issue 1, 2005, Pages 112-119

  Rao, T V V L N ^a   Sawicki, Jerzy T ^b  

^a BIRLA INSTITUTE OF TECHNOLOGY AND SCIENCE   (India)

^b Cleveland State University   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

ALGORITHMS; CAVITATION; LUBRICATION; NUMERICAL ANALYSIS; REYNOLDS NUMBER; STABILITY; SURFACE PROPERTIES; SURFACE ROUGHNESS;

CAVITATION ALGORITHMS; ROUGHNESS PATTERNS; STABILITY ANALYSIS; THRESHOLD SPEED;

JOURNAL BEARINGS;

CAVITATION; JOURNAL BEARING; LUBRICANT; SURFACE ROUGHNESS;

EID: 15044343959     PISSN: 07424787     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1828451     Document Type: Article

References (18)

1. Tzeng, S. T., and Saibel, E., 1967, "Surface Roughness Effect on Slider Bearing Lubrication," ASLE Trans., 10, p. 334.
2. Christensen, H., and Tonder, K., 1973, "The Hydrodynamic Lubrication of Rough Journal Bearings," ASME J. Lubr. Technol., 95, pp. 166-171.
3. Tripp, J. H., 1983, "Surface Roughness Effects in Hydrodynamic Lubrication: The Flow Factor Method," ASME J. Lubr. Technol., 105 pp. 458-464.
4. Patir, N., and Cheng, H. S., 1978, "An Average Flow Model for Determining Effects of Three-Dimensional Roughness on Partial Hydrodynamic Lubrication," ASME J. Lubr. Technol., 100, pp. 12-17.
5. Patir, N., and Cheng, H. S., 1979, "Application of Average Flow Model to Lubrication Between Rough Sliding Surfaces," ASME J. Lubr. Technol., 101, pp. 220-230.
6. Elrod, H. G., 1979, "A General Theory for Laminar Lubrication With Reynolds Roughness," ASME J. Lubr. Technol., 101, pp. 8-14.
7. Majumdar, B. C., and Ghosh, M. K., 1990, "Stability of a Rigid Rotor Supported on Rough Oil Journal Bearings," ASME J. Tribol., 112, pp. 73-77.
8. Ramesh, J., and Majumdar, B. C., 1995, "Stability of Rough Journal Bearings Using Nonlinear Transient Method," ASME J. Tribol., 117, pp. 691-695.
9. Elrod, H. G., 1981, "A Cavitation Algorithm," ASME J. Lubr. Technol., 103, pp. 350-354.
10. Vijayaraghavan, D., and Keith, T. G., 1990, "An Efficient, Robust and Time Accurate Numerical Scheme Applied to Cavitation Algorithm," ASME J. Tribol., 112, pp. 44-51.
11. Boedo, S., and Booker, J. F., 1997, "Surface Roughness and Structural Inertia in a Mode Based Mass-Conserving Elastohydrodynamic Lubrication Model," ASME J. Tribol., 119, pp. 449-455.
12. Wang, P., Keith, T. G., and Vaidyanathan, K., 2002, "Combined Surface Roughness Pattern and Non-Newtonian Effects on the Performance of Dynamically Loaded Journal Bearings," STLE Tribol. Trans., 123, pp. 134-143.
13. Harp, S. R., and Salant, R. F., 2001, "An Average Flow Model of Rough Surface Lubrication With Inter-Asperity Cavitation," ASME J. Tribol., 123, pp. 134-143.
14. Wang, Y., Wang, Q. J., and Lin, C., 2003, "Mixed Lubrication of Coupled Journal-Thrust Bearing Systems Including Mass Conserving Cavitation," ASME J. Tribol., 125, pp. 747-755.
15. Lund, J. W., and Thomsen, K. K., 1978, "Calculation Method and Data for the Dynamic Coefficients of Oil-Lubricated Journal Bearings," in Topics in Fluid Bearing and Rotor Bearing System Design and Optimization ASME, New York, pp. 1-28.
16. Hryniewicz, P., Szeri, A. Z., and Jahanmir, S., 2001, "Application of Lubrication Theory to Fluid Flow in Grinding: Part II-Influence of Wheel and Work-piece Roughness," ASME J. Tribol., 123, pp. 101-107.
17. Rao, T. V. V. L. N., and Sawicki, J. T., 2002, "Linear Stability Analysis for a Hydrodynamic Journal Bearing Considering Cavitation Effects," STLE Tribol. Trans., 45, pp. 450-456.
18. Rao, T. V. V. L. N., and Sawicki, J. T., 2004, "Stability Characteristics of Herringbone Grooved Journal Bearings Incorporating Cavitation Effects," ASME J. Tribol., 126, pp. 281-287.