Key inspection characteristics

Journal of Mechanical Design, Transactions of the ASME

Volumn 123, Issue 4, 2001, Pages 479-485

  Suri, Rajiv ^a   Frey, Daniel D ^a   Otto, Kevin N ^a  

^a MASSACHUSETTS INSTITUTE OF TECHNOLOGY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

EID: 13644284422     PISSN: 10500472     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1413770     Document Type: Article

References (18)

1. Frey, D., 1997, “Using Product Tolerances to Drive Manufacturing System Design,” ScD thesis, Massachusetts Institute of Technology.
2. Frey, D., Otto, K., and Taketani, S., 2001, “Manufacturing Block Diagrams and Optimal Adjustment Procedures,” ASME J. Manuf. Sci. Eng., 123, No. 1, pp. 119-127.
3. Frey, D., Otto, K., and Wysocki, J., 2000, ““Evaluating Process Capability During the Design of Manufacturing Systems,” ASME J. Manuf. Sci. Eng., 122, No. 3, pp. 513-519.
4. Soyucayli, S., and Otto, K., 1998, “Simultaneous Engineering of Quality Through Integrated Modeling,” ASME J. Mech. Des., 120, No. 2, pp. 210-220.
5. Suri, R., and Otto, K., 1999, “Variation Modeling for a Sheet Stretch Forming Manufacturing System,” CIRP Ann., 48, No. 1, pp. 397-400.
6. Harry, M., and Lawson, J., 1992, Six Sigma Producibility Analysis and Process Characterization, Addison Wesley, Reading, MA.
7. Taam, W., Subbaiah, P, and Liddy, J., 1993, “A Note on Multivariate Process Capability Indices,” J. Applied Statistics, 20, pp. 339-351.
8. Thornton, A., 1996, “Key Characteristics,” Target, 12, No. 5, pp. 14-19.
9. Thornton, A., 1997, “Using Key Characteristics to Balance Cost and Quality During Product Development,” Proc. R. Soc. London, Ser.A, September 1417, 1997, Sacramento, DETC97/DTM3899.
10. Clausing, D., 1995, “EQFD and Taguchi Effective Systems Engineering,” First Pacific Rim Symposium of Quality Development, February, Sydney.
11. Hocken, R., Raja, J., and Babu, U., 1993, “Sampling Issues in Coordinate Metrology,” Manufacturing Review, 6, No. 4, pp. 282-294.
12. Choi, W., Kurfess, T., and Cagan, J., 1998, “Sampling Uncertainty in Coordinate Measurement Data Analysis,” The Journal of the American Society for Precision Engineering, 22, No. 3, pp. 153-163.
13. Wang, Y., and Nagakar, S., 1997, “Optimal Sensor Location Design in Automated Coordinate Checking Fixtures,” Proceedings of the 1997 IEEE International Symposium on Assembly and Task Planning, Marina del Rey, CA, pp. 140-145.
14. Fussell, P, and Novic, B., 1996, “On the Manufactured Part Model Approach to Characterize Shape,” MED-Vol. 4, ASME Manufacturing Science and Engineering, pp. 463-471.
15. Khan, A., Ceglarek, D., Shi, J., and Ni, J., 1995, “An Optimal Sensor Location Methodology for Fixture Fault Diagnosis,” Manufacturing Science and Engineering, MED-Vol. 22, ASME, pp. 1165-1176.
16. Suri, R., 1999, “An Integrated System Model for Reducing Variation in Manufacturing Systems,” ScD Thesis, Massachusetts Institute of Technology, Cambridge, MA.
17. Kane, V. E., 1986, “Process Capability Indices,” J. Quality Technol., 18, No. 1, pp. 41-52.
18. Parris, A., 1996, “Precision Stretch Forming of Metal for Precision Assembly,” ScD Thesis, Massachusetts Institute of Technology, Cambridge, MA.