The effects of injector hole convergence on diesel combustion and emissions

International Journal of Vehicle Design

Volumn 36, Issue 4, 2004, Pages 385-402

  Payri, Francisco ^a   Benajes, Jesús ^a   Gonzalez C A ^a   Donde R ^b  

^a UNIVERSITAT POLITÈCNICA DE VALÈNCIA   (Spain)

^b CNR   (Italy)

Author keywords

Cavitation; Combustion; Convergence; Diesel engines; Emissions

Indexed keywords

CAVITATION; FUEL CONSUMPTION; INTERNAL COMBUSTION ENGINES; MAGNETIC FLUX; NITROGEN; NOZZLES; OXIDATION; PARTICULATE EMISSIONS; SPRAYING;

BRAKE SPECIFIC FUEL CONSUMPTION; CONVERGENCE; HEAT RELEASE RATES; SPRAY ANGLES;

DIESEL ENGINES;

EID: 11044232742     PISSN: 01433369     EISSN: None     Source Type: Journal    
DOI: 10.1504/IJVD.2004.005809     Document Type: Article

References (29)

1. Arrègle, J., Pastor, J.V. and Ruiz, S. (1999) The influence of injection parameters on diesel spray characteristics', SAE Paper 1999-01-0200.
2. Benajes, J., Molina, S., Garcia, J.M. and Riesco, J.M. (2003) 'The effect of swirl on combustion and exhaust emissions in heavy duty diesel engines', submitted to Proc. Instn Mech. Engrs, Part D: Journal of Automobile Engineering in July of 2003.
3. Benajes, J., Pastor, J.V., Payri, R. and Plazas, A.H. (2004) 'Analysis of the influence of diesel nozzle geometry in the injection rate characteristic', Journal of Fluids Engineering, Vol. 126, No. 1, p.63.
4. Corcicone, F.E., Vaglieco, B.M., and Valentino, G. (1991) 'In-cylinder fluid motion and emissions of a conventional and reentrant Diesel combustion systems', SAE Paper 911842.
5. Desantes, J.M., Arrègle, J. and Molina, S. (2000) 'Influence of the EGR rate, oxygen concentration and equivalent fuel/air ratio on the combustion behaviour and pollutant emissions of a heavy duty diesel engine', SAE Paper 2000-01-1813.
6. Dodge, L.G., Ryan, T.W. and Ryan, M. (1992) 'Effects of different injector hole shapes on diesel sprays', SAE Paper 920623.
7. Greeves, G. and Tullis, S. (1993) 'Contribution of EUI-200 and quiescent combustion system towards US94 emissions', SAE Paper 930274.
8. Heywood, J.B. (1988) Internal Combustion Engine Fundamentals, New York: McGraw-Hill.
9. Hiroyasu, H. and Arai, M. (1990) 'Structures of fuel sprays in diesel engines', SAE Paper 900475.
10. Hiroyasu, H., Arai, M. and Shimizu, M. (1991) 'Break-up length of a liquid jet and internal flow in a nozzle', In ICLASS-91, Gaithersburg, Maryland, July.
11. Ishida M. et al. (1996) 'Diesel combustion analysis based on two zone model (comparison between model analysis and experiment)', JSME Int. Journal, Series B, Vol. 39, No. 1, pp.185-192.
12. Kato, T. et al. (1998) 'Common rail fuel injection system for improvement of engine performance on heavy-duty diesel engine', SAE Paper 980806.
13. Knox-Kelecy, A. and Farrell, P. (1993) 'Spectral characteristics of turbulent flow in a scale model of a diesel fuel injector nozzle', SAE Paper 930924.
14. Lakshminarayanan, P.A., Aghav, Y.V., Dani, A.D. and Mehta, P.S. (2002) 'Accurate prediction of the rate of heat release in a modern direct injection diesel engine', Proc. Instn Mech. Engrs, Part D: Journal of Automobile Engineering, Vol. 216, No. D8, pp.663-675.
15. Lapuerta, M., Armas, O. and Bermúdez, V. (2000) 'Sensitivity of diesel engine thermodynamic cycle calculation to measurement errors and estimated parameters', Applied Thermal Engineering, Vol. 20, No. 9, pp.843-861.
16. Lapuerta, M., Armas, O. and Hernandez, J.J. (1999) 'Diagnostic of D.I. diesel combustion from in-cylinder pressure signal by estimation of mean thermodynamic properties of the gas', Applied Thermal Engineering, Vol. 5, pp.513-519.
17. Montgomery, D.T. et al. (1996) 'Effect of injector nozzle hole size and number on spray characteristics and the performance of a heavy duty D.I. diesel engine', SAE Paper 962002.
18. Payri, F., Benajes, J., Molina, S. and Riesco, J.M. (2003) 'Reduction of pollutant emissions in a HD Diesel engine by adjustment of injection parameters, boost pressure and EGR', SAE Paper 2003-01-0343.
19. Payri, R., Margot, X. and Salvador, F.J. (2002) 'A numerical study of the influence of diesel nozzle geometry on the inner cavitating flow', SAE Paper 2002-01-0215.
20. Pierpont, D.A. and Reitz, R.D. (1995) 'Effects of injection pressure and nozzle geometry on D.I. diesel emissions and performance', SAE Paper 950604.
21. Siebers, D. and Higgins, B. (2001) 'Flame lift-off on direct-injection diesel sprays under quiescent conditions', SAE Paper 2001-01-0530.
22. Siebers, D.L. (1998) 'Liquid-phase fuel penetration in diesel sprays', SAE Paper 980809.
23. Siebers, D.L. (1999) 'Scaling liquid-phase fuel penetration in diesel sprays based on mixing limited vaporization', SAE Paper 1999-01-0528.
24. Soteriou, C., Andrews, R.J. and Smith, M. (1995) 'Direct injection diesel sprays and the effect of cavitation and hydraulic flip on atomisation', SAE Paper 950080.
25. Su, T.F. et al. (1995a) 'Effects of injection pressure and nozzle geometry on spray SMD and DI emissions', SAE Paper 952360.
26. Su, T.F., Farrell, P.V. and Nagarajan, R.T. (1995b) 'Nozzle effect on high pressure diesel injection', SAE Paper 950083.
27. Tow, T.C., Pierpont, D.A. and Reitz, R.D. (1994) 'Reducing particulate and NOx emissions by using multiple injections in a heavy duty D.I. diesel engine', SAE Paper 940897.
28. Versaevel, P., Motte, P. and Wieser, K. (2000) 'A new 3D model for vaporizing diesel sprays based on mixing-limited vaporization', SAE Paper 2000-01-0949.
29. Zhang, L. et al. (1997) 'Measurement of liquid phase penetration of evaporating spray in a DI diesel engine', SAE Paper 971645.