Void-filled cold-formed rectangular hollow section braces subjected to large deformation cyclic axial loading

Journal of Structural Engineering

Volumn 128, Issue 6, 2002, Pages 746-753

  Zhao, Xiao Ling ^a   Grzebieta, Raphael ^a   Lee, Chen ^a  

^a MONASH UNIVERSITY   (Australia)

Author keywords

Bracing; Cold formed steel; Cyclic loads; Hollow sections; Thin wall sections

Indexed keywords

BUCKLING; CONCRETES; CYCLIC LOADS; DEFORMATION; METAL FORMING; STEEL; STRUCTURAL ANALYSIS; STRUCTURAL LOADS; THIN WALLED STRUCTURES;

BRACING; COLD-FORMED STEEL; HOLLOW SECTIONS; THIN WALL SECTIONS;

STRUCTURAL DESIGN;

EID: 10344258511     PISSN: 07339445     EISSN: None     Source Type: Journal    
DOI: 10.1061/(ASCE)0733-9445(2002)128:6(746)     Document Type: Article

References (54)

1. American Institute of Steel Construction (AISC). (1993). LRFD specification for structural steel buildings. Chicago.
2. American Institute of Steel Construction (AISC). (1997). Seismic provisions for structural steel buildings, Chicago.
3. Architectural Institute of Japan (AIJ). (1987). Standard for structural calculation of steel-reinforced concrete structures, 4th Ed. Tokyo.
4. Architectural Institute of Japan (AIJ). (1990). Standard for limit state design of steel structures, Tokyo.
5. Bergmann, R., Matsui, C., Meinsma, C., and Dutta, D. (1995). Design guide for concrete-filled hollow section columns under static and seismic loading, CIDECT, TÜV-Verlag GmbH, Köln, Germany.
6. Bridge, R. Q. (1976). "Concrete-filled steel tubular columns," Civ. Eng. Trans., Institution of Engineers, Australia, CE18, 127-133.
7. Bridge, R. Q., and O'Shea, M. D. (1998). "Behaviour of thin-walled steel box sections with or without internal restraint." J. Constr. Steel Res., 47(1-2), 73-91.
8. British Standards Institute (BSI). (1990). "Structural use of steelwork in building." BS5950, Part 1, London.
9. Canadian Standards Association CSA. (1989). "Steel structures for buildings." CAN/CSA-S16.1-M89, Rexdale, Ontario, Canada.
10. Cederwall, K., Engstrom, B., and Grauers, M. (1991). "High strength concrete used in composite columns." Proc., 2nd Int. Symp. on Utilization of High-Strength Concrete, American Concrete Institute (ACI), Detroit, 195-214.
11. Eurocode 3 (1992). "Design of steel structures. Part 1.1." ENV 1993-1-1, Aachen, Germany.
12. Eurocode 4 (1992). "Design of composite steel and concrete structures, Part 1.1. General rules and rules for buildings." ENV 1994-1-1, Brussels, Belgium.
13. Fujimoto, T., Nishiyama, I., Mukai, A., and Baba, T. (1995). "Test results of eccentrically loaded short columns - Square CFT columns," 2nd Joint Tech. Coordinating Committee Meeting (JTCC) on Composite and Hybrid Structures, Hawaii, 1995, 26-28.
14. Furlong, R. W. (1967). "Strength of steel-encased concrete beam-columns." J. Struct. Eng., 93(ST5), 113-124.
15. Ge, H. B., and Usami, T. (1996). "Cyclic tests of concrete filled steel box columns." J. Struct. Eng., 122(10), 1169-1177.
16. Goode, C. D., and Narayanan, R. (1997). "Design of concrete filled steel tubes to EC4." ASCCS Seminar on Concrete Filled Steel Tubes - A Comparison of International Codes and Practice, Innsbruck, Austria, 1-25.
17. Grzebieta, R. H., Zhao, X. L., and Purza F. (1997). "Multiple low cycle fatigue of SHS tubes subjected to gross pure bending." Proc., 5th Int. Colloquium on Stability and Ductility of Steel Structures, Univ. of Nagoya, Nagoya, Japan, 847-854.
18. Hajjar, J. F., Gourley, B. C., and Olson, M. (1997). "A cyclic nonlinear model for concrete-filled tubes. II: Verification." J. Struct. Eng., 123(6), 745-754.
19. Jain, A. K., Goel, S. C., and Hanson, R. D. (1980). "Hysteretic cycles of axially loaded steel members." J. Struct. Eng., 106(ST8), 1777-1795.
20. Key, P. W., and Hancock, G. J. (1986). "Plastic collapse mechanism for cold-formed square hollow section columns." Proc., 10th Australian Conf. on the Mechanics of Structures and Materials, Institution of Engineers Australia, Adelaide, Australia, 217-222.
21. Kitada, T. (1998). "Ultimate strength and ductility of state-of-the-art concrete-filled steel bridge piers in Japan." Eng. Struct., 20(4-6), 347-354.
22. Knowles, R. B., and Park, R. (1969). "Strength of concrete filled tubular columns." J. Struct. Eng., 95(ST12), 2565-2587.
23. Knowles, R. B., and Park, R. (1970). "Axial load design for concrete filled steel tubes." J. Struct. Eng., 96(ST10), 2125-2153.
24. Lee, C. (1999). "Tubular bracing members under direct and incremental cyclic loading." 4th Year Project Rep., Dept. of Civil Engineering, Monash Univ., Clayton, Victoria, Australia.
25. Lee, C., Grzebieta, R. H., and Zhao, X. L. (2000). "The importance of further study on the capacity evaluation of concrete-filled steel tubes under large deformation." Structural failure and plasticity, X. L. Zhao and R. H. Grzebieta, eds., Elsevier, Oxford, U.K., 685-690.
26. Liu, Z. Y., and Goel, S. (1988). "Cyclic load behaviour of concrete-filled tubular braces." J. Struct. Eng., 114(7), 1488-1506.
27. Matsui, C., Mitani, I., Kawano, A., and Tsuda, K. (1997). "AIJ design method for concrete filled steel tubular structures." ASCCS Seminar on Concrete Filled Steel Tubes - A Comparison of International Codes and Practice, September, Innsbruck, Austria, 93-116.
28. Murray, N. W. (1984). Introduction to the theory of thin-walled structures, Oxford Engineering Science Series, Clarendon, Oxford, U.K., 317.
29. Nakai, H., et al. (1994). "Experimental study on ultimate strength and ductility of concrete-filled thin-walled steel box columns under seismic load." J. Struct. Eng., Jpn. Soc. Civil Eng., 40A, 1401-1412.
30. Rondal, J., Wurker, K. G., Dutta, D., Wardenier, J., and Yeomans, N. (1996). Structural stability of hollow sections, Verlag TÜV Rheinland GmbH, Köln, Germany.
31. Schneider, S. P. (1998). "Axially loaded concrete-filled steel tubes." J. Struct. Eng., 124(10), 1125-1138.
32. Shakir-Khalil, H. (1991). "Tests on concrete-filled hollow section columns." Proc., 3rd Int. Conf. on Steel-Concrete Composite Structures, M. Wakabayashi, ed., Association for International Cooperation and Research in Steel-Concrete Composite Structures, Tokyo, 89-95.
33. Shakir-Khalil, H., and Zeghiche, J. (1989). "Experimental behaviour of concrete filled rolled rectangular hollow section columns." Struct. Eng., 67(9), 346-353.
34. Sherman, D., and Sully, R. M. (1994). "Tubular bracing member under cyclic loading." Proc., 4th Pacific Structural Steel Conf., Singapore Society of Steel Structures, Singapore.
35. Standards Association of Australia (SAA). (1991). "Methods for tensile testing of metals." AS1391, Sydney, Australia.
36. Standards Association of Australia (SAA). (1998). "Steel structures." AS4100-1998, Sydney, Australia.
37. Standards Association of New Zealand (NZS). (1992). "Steel structures standard." NZS 3404, Wellington, New Zealand.
38. Structural Stability Research Council (SSRC). (1991). Stability of metal structures - A world view, Bethlehem, Pa.
39. Timoshenko, S. P., and Gere, J. M. (1961), Theory of elastic stability, 2nd Ed., McGraw-Hill, Kogakusha.
40. Tomii, M., and Sakino, K. (1979). "Experimental studies on the ultimate moment of concrete filled square steel tubular beam-columns." Trans. Arch. Inst. Japan, 275 (January), 55-63.
41. Trahair, N. S., and Bradford, M. A. (1998). The behaviour and design of steel structures, Chapman and Hall, London.
42. Tubemakers. (1994). Design capacity tables for duraGal steel hollow sections, Structural Products Division of Tubemakers of Australia Limited, Newcastle, NSW, Australia.
43. Uy, B. (2000). "Strength of concrete filled steel box columns incorporating local buckling." J. Struct. Eng., 126(3), 341-352.
44. Uy, B., Wright, H. D., and Diedricks, A. A. (1998). "Local buckling of cold-formed steel sections filled with concrete." Proc., 2nd Int. Conf. Thin-Walled Structures, Singapore Society of Steel Structures, Singapore, 367-374.
45. Walpole, W. P. (1995). "Behaviour of cold-formed steel RHS members under cyclic loading." Proc., Tech. Conf. National Society for Earthquake Engineering, New Zealand Society for Earthquake Engineering, Waikanae, New Zealand, 44-50.
46. Wong, P. (1998). "Tubular bracing members under cyclic loading." 4th Year Project Rep., Dept. of Civil Engineering, Monash Univ., Clayton, Victoria, Australia.
47. Wright, H. D. (1995). "Local stability of filled and encased steel sections." J. Struct. Eng., 121(10), 1382-1388.
48. Xiao, Y. (1997). "Concrete filled steel tubular column design based on AISC LRFD methods." ASCCS Seminar on Concrete Filled Steel Tubes - A Comparison of Int. Codes and Practice, Innsbruck, Austria, 117-123.
49. Zhang, W. Z., and Shahrooz, B. M. (1999). "Comparison between ACI and AISC for concrete-filled tubular columns." J. Struct. Eng., 125(11), 1213-1223.
50. Zhao, X. L., and Grzebieta, R. H. (1999). "Void-filled SHS beams subjected to large deformation cyclic bending." J. Struct. Eng., 125(9), 1020-1029.
51. Zhao, X. L., and Hancock, G. J. (1991). "Tests to determine plate slenderness limits for cold-formed rectangular hollow sections of Grade C450." J. Australian Inst. Steel Construct., 25(4), 2-16.
52. Zhao, X. L., and Mahendran, M. (1998). "Recent innovations in cold-formed tubular sections." J. Constr. Steel Res., 46(1-3), 472-473.
53. Australian Institute of Steel Construction (AISC). (1992). Design capacity tables for structural steel hollow sections, Sydney, Australia.
54. Galambos, T. V. (1998). Guide to stability design criteria for metal structures, Wiley, New York.