Microstructural characterization of white layers formed during hard turning and grinding

Transactions of the North American Manufacturing Research Institute of SME

Volumn 32, Issue , 2004, Pages 367-374

  Guo, Y B ^a   Janowski, G M ^b  

^a University of Alabama   (United States)

^b University of Alabama at Birmingham   (United States)

Author keywords

Grinding; Hard Turning; Microstructure; White Layer

Indexed keywords

HARD TURNING; MECHANICAL DEFORMATION; MICROSTRUCTURAL CHARACTERIZATION; WHITE LAYERS;

DEFORMATION; ETCHING; MACHINING; MARTENSITE; MICROSTRUCTURE; STEEL ANALYSIS; SURFACE PROPERTIES; THERMAL EFFECTS; TRANSMISSION ELECTRON MICROSCOPY; TURNING; X RAY DIFFRACTION;

GRINDING (COMMINUTION);

EID: 10044235050     PISSN: 10473025     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (20)

1. Akcan, S., S. Shah, S.P. Moylan, P.N. Chhabra, S. Chandrasekar, and T.N. Farris, (1999), "Characteristics of White Layers Formed in Steel by Machining," ASME MED, 10, pp. 789-795.
2. Barbacki, A., M. Kawalec, and A. Hormol, (2002), "Turning and Grinding as a Source of Microstructural Changes in the Surface Layer," J. Mat. Proc. Tech., 133, pp. 21-25.
3. Barry, J. and G. Byrne, (2002), "TEM Study on the Surface White Layer in Turned Hardened Steels," Mat. Sci. Eng., A325, pp. 356-364.
4. Chou, Y. and C.J. Evans, (1998), "Process Effects on White Layer Formation in Hard Turning," NAMRI/SME, XXXVI, pp. 117-122.
5. Dawson, T.Y.G. and Kurfess, T.R., (2001), "Tool Life, Wear Rates, and Surface Quality in Hard Turning," NAMRI/SME, XXIX, pp. 258-265.
6. Eda, H., K. Kishi, and S. Hashimoto, (1981), "The Formation Mechanism of Ground White Layers," Bull. JSME, 24, pp. 743-747.
7. Field, M., W.P. Koster, J.B. Kohls, R.E. Snider, and J. Maranchik Jr., (1970), Machining of High Strength Steels with Emphasis on Surface Integrity, MRA, Inc., Columbus, OH.
8. Griffiths, B.J., (1985), "White Layer Formations at Machined Surfaces and Their Relationship to White Layer Formations at Worn Surfaces," ASME J. Tribology, 107, pp. 165-171.
9. Guo, Y.B. and J. Sahni, (2003), "A Comparative Study of the White Layer by Hard Turning vs. Grinding," Int. J. Mach. Tools & Manuf., in press.
10. König, W., M. Klinger, and R. Link, (1990), "Machining Hard Materials with Geometrically Defined Cutting Edges," Ann. CIRP, 39, p. 61.
11. Littman, W.E. and J. Wulff, (1955), "The Influence of the Grinding Process on the Structure of Hardened Steel," Trans. ASME, 47, pp. 692-714.
12. Matsumoto, Y., M.M. Barash, and C.R. Liu, (1986), "Effect of Hardness on the Surface Integrity of AISI 4340 Steel," J. Eng. Ind., 108, pp. 169-175.
13. nd Int. Mach. & Grinding Conf., Dearborn, Ml, pp. 224-308.
14. Shaw, M.C. and A. Vyas, (1994), "Heat-Affected Zones in Grinding Steel," Ann. CIRP, 43, pp. 279-282.
15. Smith, S.R., (2001), An Investigation into the Effects of Hard Turning Surface Integrity on Component Service Life, Ph.D. Dissertation, Georgia Inst. of Tech., GA.
16. Snoyes, R., M. Maris, and J. Peters, (1978), "Thermally Induced Damage in Grinding," Ann. CIRP, 27, pp. 571-581.
17. Tarasov, L.P., (1946), "Detection Causes and Prevention of Injury in Ground Surfaces," Trans. ASME, 36, pp. 389-451.
18. Töenshoff, H.K., H.G. Wobker, and D. Brandt, (1995), "Hard Turning-Influences on the Workpiece Properties," NAMRI/SME, XXIII, pp. 215-220.
19. Tomlinson, W.J., L.A. Blunt, and S. Spraggett, (1991), "The Effect of Workpiece Speed and Grinding Wheel Condition on the Thickness of White Layers," J. Mat. Proc. Tech., 25, pp. 105-110.
20. Trent, E.M. and P.K. Wright, (2000), Metal Cutting, Butterworths, London.