High-strain-rate pressure-shear recovery: A new experimental technique

International Journal of Solids and Structures

Volumn 37, Issue 12, 1999, Pages 1679-1699

  Jia, D ^a   Lennon, A M ^a   Ramesh, K T ^a  

^a Johns Hopkins University   (United States)

Author keywords

Dynamic behavior; High strain rate; Microstructural evolution; Pressure shear plate impact; Recovery

Indexed keywords

DEFORMATION; HYDROSTATIC PRESSURE; PLASTIC FLOW; SHEAR STRESS; STRAIN RATE; STRESS ANALYSIS;

MICROSTRUCTURAL EVOLUTION; PRESSURE-SHEAR PLATE IMPACT;

STRUCTURAL ANALYSIS;

EID: 0346053699     PISSN: 00207683     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0020-7683(98)00278-9     Document Type: Article

References (22)

1. Chichili, D.R., 1997. High-strain-rate deformation mechanisms and adiabatic shear localization in alpha-titanium. Ph.D. Dissertation, The Johns Hopkins University.
2. 3 metal-matrix composite. International Journal of Solids and Structures 32 (17/18), 2609-2626.
3. Chichili, D.R., Ramesh, K.T., Hemker, K.J., 1998. The high-strain-rate response of alpha-titanium: experiments, deformation mechanisms, and modeling. Acta Materialia 46 (3), 1025-1043.
4. Clifton, R.J., Klopp, R.W., 1980. Pressure-shear plate impact testing. ASM Metals Handbook, vol. 8. ASM International, OH, p. 230.
5. da Silva, M.G., Ramesh, K.T., 1997. The rate-dependent deformations of porous pure iron. International Journal of Plasticity 13 (6-7), 587-610.
6. Duffy, J., Campbell, J.D., Hawley, R.H., 1971. On the use of a torsional split Hopkinson bar to study rate effects in 1100-0 aluminum. Trans. ASME: J. Appl. Mech 38, 83-91.
7. Follansbee, P.S., Gray, G.T., 1989. An analysis of the low temperature, low and high strain-rate deformation of Ti-6Al-4V. Metall. Trans. A 20A, 863.
8. Grebe, H.A., Pak, H., Meyers, M.A., 1985. Adiabatic shear localization in titanium and Ti-6 Pet Al-4 Pet V alloy. Metall. Trans. A 16A, 761.
9. Kim, K.S., Clifton, R.J., 1977. A combined normal- and transverse-displacement interferometer with an application to impact of y-cut quartz. Journal of Applied Physics 48, 4132.
10. Kobayashi, H., 1987. Shear localization and fracture in torsion of metals. Ph.D. Thesis, University of Reading.
11. Kolsky, H., 1949. An investigation of the mechanical properties of materials at very high rates of loading. Proc. Phys. Society, 62B, p. 676.
12. Kumar, P., Clifton, R.J., 1979. Dislocation motion and generation in LiF crystals subjected to plate impact. Journal of Applied Physics 50, 4747.
13. Machcha, A.R., Nemat-Nasser, S., 1994. Pressure-shear recovery experiments. Mechanics of Materials 18, 49.
14. Mecking, H., Kocks, U.F., 1981. Kinetics of flow and strain-hardening. Acta Metall. Mater. 29, 1865.
15. Nemat-Nasser, S., Isaacs, J.B., Starrett, J.E., 1991. Hopkinson techniques for dynamic recovery experiments. Proc. R. Soc. Lond. A, 435, p. 371.
16. Ramesh, K.T., Kelkar, N., 1995. Technique for the continuous measurement of the projectile velocity in plate impact experiments. Rev. Sci. Instrum. 66, 3034.
17. Ramesh, K.T., Clifton, R.J., 1992. Finite deformation analysis of pressure-shear plate impact experiments on elastohydrodynamic lubricants. Journal of Applied Mechanics 59 (4), 754-761.
18. Yadav, S., Ramesh, K.T., 1995. The mechanical properties of tungsten-based composites at very high strain rates. Materials Science & Engineering A 203, 140-153.
19. 3 metal-matrix composite at high rates of deformation. Acta Metallurgica 43 (12), 4453-4464.
20. Yadav, S., Davis, J.A., Ramesh, K.T., 1993. Damage and recovery experiments using pressure-shear plate impact. In: Ramesh, K.T. (Ed.), Experimental Techniques in the Dynamics of Deformable Solids, ASME AMD, vol. 165, pp. 71-78.
21. Yoo, M.H., 1981. Slip, twinning, and fracture in hexagonal close-packed metals. Metall. Trans. A 12A, 409.
22. Zerilli, P.J., Armstrong, R.W., 1987. Dislocation-mechanics-based constitutive relations for material dynamic calculations. Journal of Applied Physics 61, 1816.