Impregnation molding of particle-filled preceramic polymers: process modeling

Journal of the American Ceramic Society

Volumn 82, Issue 8, 1999, Pages 2017-2028

  Erdal, Merve ^a   Güçeri, Selçuk I ^b   Danforth, Stephen C ^c  

^a UNIVERSITY OF MINNESOTA   (United States)

^b 1120 Science and Engineering Offices   (United States)

^c RUTGERS UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTER SIMULATION; FILLERS; FILTRATION; FLOW OF SOLIDS; IMPREGNATION; INJECTION MOLDING; MATHEMATICAL MODELS; PARTICLES (PARTICULATE MATTER); VOLUME FRACTION;

FIBER CERAMIC COMPOSITES; IMPREGNATION MOLDING; INJECTION FLOW; PRECERAMIC POLYMERS;

CERAMIC FIBERS;

EID: 0343962688     PISSN: 00027820     EISSN: None     Source Type: Journal    
DOI: 10.1111/j.1151-2916.1999.tb02034.x     Document Type: Article

References (28)

1. J. R. Strife, J. J. Brennan, and K. M. Prewo, "Status of Continuous Fiber-Reinforced Ceramic Matrix Composite Processing Technology," Ceram. Eng. Sd. Proc., 11 [7/8] 871-919 (1990).
2. S. Güçeri, Fluid Flow Problems in Processing of Composite Materials (Lecture Notes). University of Illinois at Chicago, Chicago, IL, 1994.
3. T. Erny, M. Seibold, O. Jarchow, and P. Greil, "Microstructure Development of Oxycarbide Composites during Active-Filler-Controlled Polymer Pyrolysis," J. Am. Ceram. Soc., 76 [1] 207-13 (1993).
4. M. Seibold, B. Ahlers, and P. Greil, "Plastic Forming of Polymer-Metal Blends for the Fabrication of Ceramic Matrix Composites"; p. 555 in Advanced Structural Inorganic Composites. Edited by P. Vincencini. Elsevier, Amsterdam, The Netherlands, 1991.
5. J. P. Coulter and S. Güçeri, "Resin Transfer Molding: Process Review, Modeling and Research Opportunities"; pp. 79-86 in The Manufacturing Science of Composites, Vol. IV. Edited by T. G. Gutowski. ASME Publications, New York, 1988.
6. P. Greil and M. Seibold, "Modeling of Dimensional Changes during Polymer-Ceramic Conversion for Bulk Component Fabrication," J. Mater. Sci., 27, 1053-60 (1992).
7. S.-M. Sim and R. J. Kerans, "Slurry Infiltration of 3-D Woven Composites," Ceram. Eng. Sci. Proc., 13 [9/10] 632-41 (1992).
8. P. Greil and M. Seibold, "Active Filler Controlled Pyrolysis (AFCOP) - A Novel Fabrication Route to Ceramic Composite Materials"; pp. 43-49 in Ceramic Transactions, Vol. 19, Advanced Composite Materials. Edited by M. D. Sacks. American Ceramic Society, Westerville, OH, 1991.
9. J. P. Coulter, "Resin Impregnation During the Manufacturing of Composite Materials"; Ph.D. Dissertation. University of Delaware, Newark, DE, 1988.
10. M. V. Brushke and S. G. Advani, "A Finite Element/Control Volume Approach to Mold Filling in Anisotropic Porous Media," Polym. Compos., 11 [6] 398-405 (1990).
11. ™ Ceramic Composites," Ceram. Eng. Sci. Proc., 16 [4] 191-99 (1995).
12. D. W. Vogel and U. Spelz, "Cost Effective Production Techniques for Continuous Fiber Reinforced Ceramic Matrix Composites"; pp. 255-59 in Ceramic Transactions, Vol. 51, Ceramic Processing Science and Technology. Edited by H. Hausner, G. L. Messing, and S.-I. Hirano. American Ceramic Society, Westerville, OH, 1995.
13. M. Erdal, "Impregnation Molding Of Continuous Fiber-Reinforced Ceramic-Ceramic Composites Using Preceramic Polymers"; Ph.D. Dissertation. University of Illinois, Chicago, IL, 1998.
14. J. H. D. Hampton, S. B. Savage, and R. A. L. Drew, "Modelling Clogging During Filtration of Ceramic Suspensions," Br. Ceram. Trans., 91 [4] 103-107 (1992).
15. J. H. D. Hampton, S. B. Savage, and R. A. L. Drew, "Experimental Analysis of Fine-Particle Migration during Ceramic Filtration Process," J. Am. Ceram. Soc., 75 [10] 2726-32 (1992).
16. A. P. Philipse, B. C. Bonekamp, and H. J. Veringa, "Colloidal Filtration and (Simultaneous) Sedimentation of Alumina and Silica Suspensions: Influence of Aggregates," J. Am. Ceram. Soc., 73 [9] 2720-27 (1990).
17. J. E. Tobiason, G. S. Johnson, P. K. Westerhoff, and V. Balasubramaniam, "Particle Size and Chemical Effects on Contact Filtration Performance," J. Environ. Eng. (NY), 119 [3] 520-39 (1993).
18. C. R. O'Melia and W. Ali, "The Role of Retained Particles in Deep Bed Filtration," Prog. Water Technol., 10 [5/6] 167-82 (1978).
19. S. Veerapaneni and M. R. Wiesner, "Role of Suspension Polydispersivity in Granular Media Filtration," J. Environ. Eng. (NY), 119 [1] 172-88 (1993).
20. J. P. Herzig, D. M. Ledere, and P. Le Goff, "Flow of Suspensions through Porous Media-Application to Deep Bed Filtration," Ind. Eng. Chem., 62 [5] 8-35 (1970).
21. K. J. Ives, "Mathematical Models of Deep Bed Filtration"; pp. 183-224 in Proceedings of NATO Advanced Study Institute, The Scientific Basis of Filtration. Edited by K. J. Ives, Noordhoff, Leyden, The Netherlands, 1975.
22. A. Adin and M. Rebhun, "A Model to Predict Concentration and Head-Loss Profiles in Filtration," J. Am. Water Works Assoc., 69, 444-53 (1977).
23. J. E. Tobiason and C. R. O'Melia, "Physicochemical Aspects of Particle Removal in Depth Filtration," J. Am. Water Works Assoc., 80 [12] 54-64 (1988).
24. A. B. Metzner, "Rheology of Suspensions in Polymeric Liquids," J. Rheol. (NY), 29 [6] 739-75 (1985).
25. T. Kataoka, T. Kitano, M. Sasahara, and K. Nishijima, "Viscosity of Particle Filled Polymer Melts," Rheol. Acta, 17, 149-55 (1978).
26. D. L. Trafford, "Computational Analysis and Simulation of the Mold Filling Process for Hele-Shaw Flows"; Master's Dissertation. University of Delaware, Newark, DE, 1987.
27. S. Subbiah, D. L. Trafford, and S. Güceri, "Non-isothermal Flow of Polymers into Two-Dimensional, Thin Cavity Molds: A Numerical Grid Generation Approach," Int. J. Heat Mass Transfer, 32 [3] 415-34 (1989).
28. S. Güçeri, "Finite Difference Solutions of Field Problems"; pp. 141-236 in Fundamentals of Computer Modeling for Polymer Processing. Edited by C. Tucker III. Hanser, New York, 1989.