Effect of surface topography of workpiece on pressure dependence of coefficient of friction in sheet metal forming

CIRP Annals - Manufacturing Technology

Volumn 47, Issue 1, 1998, Pages

  Azushima, Akira ^a   Miyamoto, Junji ^a   Kudo, Hideaki ^a  

^a NONE

Author keywords

Sheet metal; Topography; Tribology

Indexed keywords

ALUMINUM ALLOYS; ALUMINUM SHEET; FLUORESCENCE; FRICTION; INTERFACES (MATERIALS); PRESSURE EFFECTS; SURFACE MEASUREMENT; SURFACE ROUGHNESS;

FRICTION COEFFICIENT; SURFACE TOPOGRAPHY;

METAL FORMING;

EID: 0343830913     PISSN: 00078506     EISSN: None     Source Type: Journal    
DOI: 10.1016/s0007-8506(07)62879-0     Document Type: Article

References (12)

1. Emmens, W.C., 1988, The Influence of Surface Roughness on Friction, Proc. 15th IDDRG Gongress, 63-70.
2. Weinmann, K. J., Bhonsle, S.R. and Gerstenberger, J., 1990, On the Determination of the Coefficient of Friction and the Friction Factor by the Strip-Tension Test, Ann. CIRP, 39: 263-266.
3. Wilson, W.R.D., Malkani, H.G. and Saha, P.K., 1991, Boundary Friction Measurements Using a New Sheet Metal Forming Simulator, Proc. NAMRI/SME, 37-42.
4. Ike, H. et. I., 1991, Simulation Test of the Sliding Characteristics of Couted Steel Sheets in Autobody-Panel Forming, Proc. 18th IDDRG Congress, 173-178.
5. Azushima, A., Igarashi, K. and Imai, K., 1997, Proposal of a New Simulation Method by Means of Tribometer Controlled by Computer for Sheet Metal Forming and Evaluation of Tribological Properties of Lubricant for Aluminum Alloy Sheet, J. Japan Soc. Technol. of Plasticity, 38:469-474.
6. Azushima, A., 1995, Direct Observation of Contact Behaviour to Interpret the Pressure Dependence of the Coefficient of Friction in Sheet Metal Forming, Ann. CIRP, 44: 209-212.
7. Balbach, R., 1987, Influence of Various Surface Microstructures on the Tribology in Aluminum Sheet Metal Forming, Ann. CIRP, 36: 181-184.
8. Felder, E. and Samper, V.,1994, Experimental Study and Theoretical Interpretation of the Frictional Mechanisms in Steel Sheet Forming, Wear, 178: 85-94.
9. Geiger, M., Engel, U. and Pfestorf, M., 1997, New Developments for the Qualification of Technical Surfaces in Forming Processes, Ann. CIRP, 46: 171-174.
10. Schmoeckel, D., Pier, M. and Staeves, J., 1997, Topography Deformation of Sheet Metal during the Forming Process and Its Influence on Friction, Ann. CIRP, 46: 175-178.
11. Azushima, A., Sugai, T. and Natsui, M., 1995, Observation of Microcontact Behavior at Interface between Roll and Workpiece by Means of Fluorescence Measurement Method, Proc. 46th Japanese Joint Conf. Technol. of Plasticity, 311-314.
12. Azushima, A., Ohtsuka, K., Inagaki, S. and Kitaguchi, A., 1997, Quantitative Analysis of Lubricant Film at Interface between Tool and Workpiece by Means of Fluorescence Microscopic Measurement Method with Image Processor, Proc. Japanese Spring Conf. Technol. of Plasticity, 319-323.