Experimental study of showerhead cooling on a cylinder comparing several configurations using cylindrical and shaped holes

Journal of Turbomachinery

Volumn 122, Issue 1, 2000, Pages 161-169

  Reiss, H ^a   Bolcs A ^a  

^a EPFL   (Switzerland)

Author keywords

[No Author keywords available]

Indexed keywords

BLOWING RATIO; COOLING CONFIGURATION; COOLING PERFORMANCE; CYLINDER DIAMETERS; CYLINDER MODEL; CYLINDRICAL HOLES; DENSITY RATIO; EXPANDED HOLES; EXPERIMENTAL STUDIES; FILM COOLING; FILM COOLING EFFECTIVENESS; FLOW CONDITION; FREE JETS; GAS CONSUMPTION; GAS INJECTION; GAS TURBINE BLADES; HEAT TRANSFER MEASUREMENTS; LEADING EDGE; LENGTH SCALE; LOCAL HEAT TRANSFER COEFFICIENT; MAINSTREAM TURBULENCE; PERFORMANCE ENHANCEMENTS; SHAPED HOLES; SHOWERHEAD; SURFACE DISTRIBUTIONS; THERMOCHROMIC LIQUID CRYSTALS; UNCOOLED;

CARBON DIOXIDE; COOLING; EXPERIMENTS; LIQUID CRYSTALS; MACH NUMBER; REYNOLDS NUMBER;

CYLINDER CONFIGURATIONS;

COOLING; CYLINDER; FILM; GAS TURBINE; HEAT TRANSFER;

EID: 0342700194     PISSN: 0889504X     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.555420     Document Type: Article

References (12)

1. Beeck, A., Fottner, L., Benz, E., and Wittig, S., 1993, "The aerodynamic effect of coolant ejection in the leading edge region of a film cooled turbine blade," Heat Transfer and Cooling in Gas Turbines, Vol. AGARD-CP-527, Paper 35.
2. Bittlinger, G., Schulz, A., and Wittig, S., 1994, "Film cooling effectiveness and heat transfer coefficients for slot injection at high blowing ratios," ASME Paper No. 94-GT-182.
3. Drost, U., and Bölcs, A., 1999, "Investigation of Detailed Film Cooling Effectiveness and Heat Transfer Distributions on a Gas Turbine Airfoil," ASME JOURNAL OF TURBOMACHINERY, Vol. 121, pp. 233-232.
4. Drost, U., Bölcs, A., and Hoffs, A., 1997, "Utilization of the Transient Liquid Crystal Technique for Film Cooling Effectiveness and Heat Transfer Investigations on a Flat Plate and a Turbine Airfoil," ASME Paper No. 97-GT-26.
5. Giebert, D., Gritsch, M., Schulz, A., and Wittig, S., 1997, "Film-Cooling Holes With Expanded Exits: A Comparison of Computational Results With Experiments," ASME Paper No. 97-GT-163.
6. Goldstein, R. J., and Eckert, E. R. G., 1973, "Effects of hole geometry and density on three-dimensional film cooling," Journal of Heat and Mass Transfer, Vol. 17, pp. 595-607.
7. Gritsch, M., Schulz, A., and Wittig, S., 1998, "Adiabatic Wall Effectiveness Measurements of Film-Cooling Holes With Expanded Exits," ASME JOURNAL OF TURBOMACHINERY, Vol. 120, pp. 549-556.
8. Hoffs, A., Drost, U., and Bölcs, A., 1997, "An Investigation of Effectiveness and Heat Transfer on a Showerhead-Cooled Cylinder," ASME Paper No. 97-GT-69.
9. Mehendale, A. B., and Han, J.-C., 1993, "Reynolds number effect on leading edge film effectiveness and heat transfer coefficient," Int. Journal of Heat and Mass Transfer, Vol. 36, No. 15, pp. 3723-3730.
10. 2 film injection: Part II - Effect on film effectiveness and heat transfer distributions," ASME JOURNAL OF TURBOMACHINERY, Vol. 116, pp. 730-737.
11. Vedula, R. J., and Metzger, D. E., 1991, "A method for the simultaneous determination of local effectiveness and heat transfer distributions in three-temperature convection situations," ASME Paper No. 91-GT-345.
12. Wittig, S., Schulz, A., Gritsch, M., and Thole, K. A., 1996, "Transonic Film-Cooling Investigations: the Effects of Hole Shapes and Orientations," ASME Paper No. 96-GT-222.