An improved transient model of tool temperatures in metal cutting

Journal of Manufacturing Science and Engineering, Transactions of the ASME

Volumn 123, Issue 1, 2001, Pages 30-37

  Jen, Tien Chien ^a   Anagonye, Aloysius U ^b  

^a University of Wisconsin Milwaukee   (United States)

^b GENERAL MOTORS CORPORATION   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

EID: 0242655671     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.1334865     Document Type: Article

References (21)

1. Trigger, K. J., and Chao, B. T., 1951, “An Analytical Evaluation of Metal Cutting Temperatures,” Trans. ASME, 73, pp. 57-68.
2. Barrow, G., 1973, “A Review of Experimental and Theoretical Techniques for Assessing Cutting Temperatures,” CIRP Ann., 22, pp. 203-211.
3. Shaw, M. C., 1984, Metal Cutting Principles, Oxford University Press, Oxford, Chap. 12.
4. Boothroyd, G., and Knight, W. A., 1989, Fundamentals of Machining and Machine Tools, Marcel and Dekker, New York, Chap. 3.
5. Strenkowski, J. S., and Moon, K. J., 1990, “Finite Element Prediction of Chip Geometry and Tool/Workpiece Temperature Distribution in Orthogonal Machining,” ASME J. Eng. Ind., 112, pp. 313-318.
6. Stephenson, D. A., 1991, “Assessment of Steady-State Metal Cutting Temperature Models Based on Simultaneous Infrared and Thermocouple Data,” ASME J. Eng. Ind., 113, pp. 121-128.
7. Chandra, A., and Chen, C. L., 1994, “Thermal Aspects of Machining: A BEM Approach,” Int. J. Solids Struct., 33, pp. 1657-1693.
8. Stephenson, D. A., and Ali, A., 1992, “Tool Temperature in Interrupted Cutting,” ASME J. Eng. Ind., 114, pp. 127-136.
9. Radulescu, R., and Kapoor, S. G., 1994, “An Analytical Model for Prediction of Tool Temperature Fields during Continuous and Interrupted Cutting,” ASME J. Eng. Ind., 116, pp. 135-143.
10. Stephenson, D. A., Jen, T. C., and Lavine, A. S., 1997, “Cutting Tool Temperatures in Contour Turning: Transient Analysis and Experimental Verification,” ASME J. Manuf. Sci. Eng., 119, pp. 494-501.
11. Loewen, E. G., and Shaw, M. C., 1954, “On the Analysis of Cutting Tool Temperatures,” Trans. ASME, 76, pp. 217-231.
12. Carslaw, H. S., and Jaeger, J. C., 1959, Conduction of Heat in Solids, Clarendon Press, Oxford.
13. Jen, T. C., and Lavine, A. S., 1994, “Prediction of Tool Temperatures in Interrupted Metal Cutting,” Proc. of 7th International Symposium on Transport Phenomena in Manufacturing Processes, pp. 211-216.
14. Kagiwada, T., and Kanauchi, T., 1988, “Numerical Analyses of Cutting Temperatures and Flow Ratios of Generated Heat,” JSME Int. J., Ser. III, 31, No. 3, pp. 624-633.
15. Chao, B. T., and Trigger, K. J., 1955, “Temperature Distribution at the Tool-Chip Interface in Metal Cutting,” Trans. ASME, 77, pp. 1107-1121.
16. Levy, E. K., Tsai, C. L., and Groover, M. P., 1976, “Analytical Investigation of the Effect of Tool Wear on the Temperature Variations in a Metal cutting Tool,” ASME J. Eng. Ind., 98, pp. 251-257.
17. Tsai, C. L., 1973, Finite Difference Solutions for the Time Dependent Temperature Distributions in Metal Cutting Tool, MS thesis, Department of Mechanical Engineering and Mechanics, Lehigh University.
18. Komanduri, R., 1993, “Machining and Grinding: A Historical Review of the Classical Papers,” Appl. Mech. Rev., 46, No. 3, pp. 80-132.
19. Jaeger, J. C., 1942, “Moving Sources of Heat and the Temperature at Sliding Contacts,” Proc. Roy. Soc. NSW, 76, pp. 203-224.
20. Blok, H., 1938, “Theoretical Study of Temperature Rise at Surfaces of Actual Contact Under Oiliness Lubricating Conditions,” Proc. General Discussion on Lubrication and Lubricants, Inst. Mech. Eng. (London), pp. 222-235.
21. Trent, E. M., 1977, Metal Cutting, Butterworth, Washington, DC, Chap. 5.