Heat transfer from a flat plate to a turbulent axisymmetric impinging jet

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science

Volumn 211, Issue 2, 1997, Pages 167-172

  Ashforth Frost, S ^a   Jambunathan, K ^a   Whitney, C F ^a,b   Ball, S J ^a  

^a NOTTINGHAM TRENT UNIVERSITY   (United Kingdom)

^b European Gas Turbines Limited   (United Kingdom)

Author keywords

Forced convection; Heat transfer; Jet impingement; Liquid crystal thermography

Indexed keywords

COOLING; HEATING; JETS; NOZZLES; PLATES (STRUCTURAL COMPONENTS); THERMOGRAPHY (IMAGING); TURBULENT FLOW;

FORCED CONVECTION;

HEAT TRANSFER;

HEAT TRANSFER; JET IMPINGEMENT; PLATES;

EID: 0141947410     PISSN: 09544062     EISSN: None     Source Type: Journal    
DOI: 10.1243/0954406971521746     Document Type: Article

References (17)

1. Button, B. L. and Wilcock, D. Impingement heat transfer -a bibliography 1890-1975. Previews Heat Mass Transfer, 1978, 4(3), 83-89.
2. Button, B. L. and Jambunathan, K. Jet impingement heat transfer: a bibliography 1976-1985. Previews Heat Mass Transfer, 1989, 15(2), 149-178.
3. Jambunathan, K. and Button, B. L. Jet impingement heat transfer: a bibliography 1986-1991. Previews Heat Mass Transfer, 1994, 20(5), 385-413.
4. Ashforth-Frost, S. and Jambunathan, K. Effect of nozzle geometry and semi-confinement on the potential core of a turbulent axisymmetric free jet. Int. Commun. Heat Mass Transfer, 1996, 23(2), 155-162.
5. Goldstein, R. J. and Franchett, M. E. Heat transfer from a flat plate to an oblique impinging jet. Trans. ASME, J. Heat Transfer, 1988, 110, 84-90.
6. Jambunathan, K., Ashforth-Frost, S. A. and Whitney, C. F. Design of surface heaters for liquid crystal thermography. In IMechE Seminar on Optical Methods and Data Processing in Heat and Fluid Flow, City University, London, 14-15 April 1994, pp. 43-47.
7. Simonich, J. C. and Moffat, R. J. New technique for mapping heat transfer coefficient contours. Rev. Sci. Instrum., 1982, 53(5), 678-683.
8. Baughn, J. W., Hoffman, M. A. and Makel, D. B. Improvements in a new technique for measuring and mapping heat transfer coefficients. Rev. Sci. Instrum., 1986, 57(4), 650-654.
9. Ashforth-Frost, S., Jambunathan, K. and Whitney, C. F. Velocity and turbulence characteristics of a semi-confined orthogonally impinging slot jet. In Tenth Symposium on Turbulent Shear Flow, Pittsburgh, Pennsylvania, 14-16 August 1995, Vol. 1, no. 10, pp. 1-6.
10. Button, B. L. and Tura, R. Design of a blower type low speed thermal wind tunnel. Department of Mechanical Engineering report ME.383, Coventry Lanchester Polytechnic, 1984.
11. BS 1042: 1983 The Measurement of Fluid Flow in Closed Conduit. Section 2.1: Methods Using Pilot-Static Tubes (British Standards Institution, London).
12. Kline, S. J. and McClintock, F. A. Describing uncertainties in single-sample experiments. Mech. Engng, 1953, 75, 3-8.
13. Obot, N. T., Majumdar, A. S. and Douglas, W. J. M. Effect of semi-confinement on impingement heat transfer. In Proceedings of Seventh International Heat Transfer Conference, Munich, 6-10 September 1982, Vol.3, pp. 395-400.
14. Kezios, S. P. Heat transfer in the flow of a cylindrical air jet normal to an infinite plane. PhD thesis, Illinois Institute of Technology, Chicago, Illinois, 1956.
15. Gardon, R. and Akfirat, J. C. The role of turbulence in determining heat transfer characteristics of impinging jets. Int. J. Heat Mass Transfer, 1965, 8, 1261-1272.
16. Baughn, J. W. and Shimizu, S. Heat transfer measurements from a surface with uniform heat flux and an impinging jet. Trans. ASME, J. Heat Transfer, 1989, 111, 1096-1098.
17. Van, X., Baughn, J. W. and Mesbah, M. The effect of Reynolds number on the heat transfer distribution from a flat plate to an impinging jet. Trans. ASME, Heat Transfer Division: Fundamental and Applied Heat Transfer Research for Gas Turbine Engines, 1992, 226, 1-7.