Film cooling characteristics of a single round hole at various streamwise angles in a crossflowPart II: Heat transfer coefficients

International Journal of Heat and Mass Transfer

Volumn 46, Issue 2, 2003, Pages 237-249

  Yuen, C H N ^a   Martinez Botas, R F ^a  

^a IMPERIAL COLLEGE LONDON   (United Kingdom)

Author keywords

[No Author keywords available]

Indexed keywords

COOLING; HEAT TRANSFER COEFFICIENTS; THIN FILMS;

FILM COOLING;

HEAT TRANSFER;

COOLING; CROSSFLOW; FILM; HEAT TRANSFER; MATHEMATICAL ANALYSIS; MODELING;

EID: 0141683857     PISSN: 00179310     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0017-9310(02)00273-9     Document Type: Article

References (26)

1. C.H.N. Yuen, R.F. Martinez-Botas, Film cooling characteristics of a single round hole at various angles in a crossflow: Part I-effectiveness, Int. J. Heat Mass Transfer 46 (2003), PII: S0017-9310(02)00274-0
2. Eriksen V.L. Goldstein R.J. Heat transfer and film cooling following injection through inclined circular tubes ASME J. Heat Transfer May 1974 239-245
3. Goldstein R.J. Yoshida T. Boundary layer and laminar injection on film cooling performance ASME J. Heat Transfer 104 1982 355-362
4. Hay N. Lampard D. Saluja C.L. Effects of cooling films on the heat transfer coefficient on a flat plate with zero mainstream pressure gradient J. Eng. Gas Turbines Power 107 1985 105-110
5. Ammari H.D. Hay N. Lampard D. The effect of density ratio on the heat transfer coefficient from a film-cooled flat plate ASME J. Turbomach. 112 1990 444-450
6. Loftus P.J. Jones T.V. The effect of temperature ratios on the film cooling process ASME J. Eng. Power 105 1983 615-621
7. Ligrani P.M. Ortiz A. Joseph S.L. Evans D.L. Effects of embedded vortices on film-cooled turbulent boundary layers ASME J. Turbomach. 111 1989 71-77
8. Ligrani P.M. Ciriello S. Bishop D.T. Heat transfer, adiabatic, effectiveness, and injectant distributions downstream of a single row and two staggered rows of compound angle film-cooling holes ASME J. Turbomach. 14 1992 687-700
9. Schmidt D.L Sen B. Bogard D.G. Film cooling with compound angle holes: Adiabatic effectiveness ASME J. Turbomach. 118 1996 807-813
10. Sen B. Schmidt D.L. Bogard D.G. Film cooling with compound angle holes: Heat transfer ASME J. Turbomach. 118 1996 800-806
11. S.W. Burd, T.W. Simon, Measurements of discharge coefficients in film cooling, ASME Paper No. 98-GT-009, 1998
12. S.W. Burd, T.W. Simon, Turbulence spectra and length scales measured in film coolant flows emerging from discrete holes, ASME Paper No. 98-GT-190, 1998
13. A.L. Brundage, M.W. Plesniak, S. Ramadhyani, Influence of coolant feed direction and hole length on film cooling jet velocity profiles, ASME Paper No. 99-GT-35, 1999
14. Walters D.K. Leylek J.H. A detailed analysis of film cooling physics: Part I-streamwise injection with cylindrical holes ASME J. Turbomach. 122 2000 102-112
15. S. Lloyd, A. Brown, Fluid flow and heat transfer characteristics in the entrance region of circular pipes, ASME Paper No. 85-GT-120, 1985
16. Andrews G.E. Alikhanizadeh M. Asere A.A. Hussain C.I. Khoshkbar M.S. Azari M.S. Mkpadi M.C. Small diameter film cooling holes: Wall convective heat transfer ASME J. Turbomach. 108 1986 283-289
17. Cho H.H. Goldstein R.J. Heat (mass) transfer and film cooling effectiveness with injection through discrete holes: Part I-within holes and on the back surface ASME J. Turbomach. 117 1995 440-449
18. Baughn J.W. Liquid crystal methods for studying turbulent heat transfer Int. J. Heat Fluid Flow 16 5 1995 365-375
19. C.H.N. Yuen, Measurement of local heat transfer coefficient and film cooling effectiveness ion film cooling geometries, Ph.D. thesis, University of London, Imperial College of Science, Technology and Medicine, London, 2000
20. Mick W.J. Mayle R.E. Stagnation film cooing and heat transfer, including its effect within the hole pattern ASME J. Turbomach. 110 1988 66-72
21. A.K. Rastogi, Effectiveness and heat transfer of three-dimensional film cooling slots, Ph.D. thesis, University of London, Imperial College of Science, Technology and Medicine, London, 1972
22. V.L. Eriksen, Film cooling effectiveness and heat transfer with injection through holes, Ph.D. thesis, University of Minnesota, 1971
23. Wang T. Simon T.W. Buddhavarapu J. Heat transfer and fluid mechanics measurements in transitional boundary layer flows ASME J. Eng. Gas Turbines Power 107 1985 1007-1015
24. Ligrani P.M. Williams W. Effects of an embedded vortex on injectant from a single film-cooling hole in a turbulent boundary layer ASME J. Turbomach. 112 1990 428-436
25. Kline S.J. McClintock F.A. Describing uncertainties in single-sample experiments Mech. Eng. January 1953 3-8
26. Schneider P.J. Conduction Heat Transfer sixth ed. 1974 Addison-Wesley Reading, MA