Performance of welded high-strength low-alloy steels in sour environments

Corrosion

Volumn 59, Issue 7, 2003, Pages 640-653

  Omweg, G M ^a   Frankel, G S ^a   Bruce, W A ^b   Ramirez, J E ^b   Koch, G ^c  

^a OHIO STATE UNIVERSITY   (United States)

^b EDISON WELDING INSTITUTE   (United States)

^c CC Technologies USA   (United States)

Author keywords

Hydrogen embrittlement; Hydrogen sulfide cracking test; Pipelines; Steel; Sulfide stress cracking; Weld

Indexed keywords

EXTRAPOLATION; HARDNESS; PLASTIC DEFORMATION; STRESSES; SULFIDE CORROSION CRACKING;

CENTERLINE SEGREGATION REGION (CSR);

STEEL;

HYDROGEN EMBRITTLEMENT; HYDROGEN SULFIDE; LOW ALLOY STEEL; PERFORMANCE ASSESSMENT; PIPELINE; STRESS CORROSION CRACKING; WELDED JOINT;

EID: 0037997609     PISSN: 00109312     EISSN: None     Source Type: Journal    
DOI: 10.5006/1.3277595     Document Type: Article

References (18)

1. B.J. Berkowitz, F.H. Heubaum, Corrosion 40, 5 (1984): p. 240.
2. R. D. Kane, Int. Met. Rev. 30, 6 (1985): p. 291.
3. J.C. Turn, B.E. Wilde, C.A. Troianos, Corrosion 39, 9 (1983): p. 364.
4. NACE Standard Materials Requirements, "Sulfide Stress Cracking Resistant Metallic Materials for Oilfield Equipment" (Houston, TX: NACE International, 1994), p. 1.
5. 2S Environments" (Houston, TX: NACE International, 1996).
6. R.A. Walker, The Significance of Local Hard Zones on the Outside of Pipeline Girth Welds (Cambridge, U.K.: The Welding Institute, 1989), p. 1.
7. G. Omweg, "Sulfide Stress Cracking Resistance of Welded High Strength Low-Alloy Steels" (MS thesis, Materials Science and Engineering Department, The Ohio State University, 2001).
8. G.M. Omweg, G.S. Frankel, W.A. Bruce, G. Koch, Weld J. 82 (2003): p. 136-144S.
9. M.S. Cayard, R.D. Kane, Corrosion 53, 3 (1997): p. 227.
10. W.B. Morrison, 'Status of Microalloyed (HSLA) Steel Development." eds. J.T. Hickey, D.G. Howden, M.D. Randall, Proc. Int. Conf. Metall., Weld., Qualif. Microalloyed (HSLA) Steel Weldments (Miami. FL: American Welding Society, 1990).
11. "Sulfide Stress Cracking Resistance of Pipeline Welds," Mater. Perform. 32, 1 (1993): p. 58-64.
12. D.P. Fairchild, N.V. Bangaru, J.Y. Koo, P.L. Harrison, A. Ozekcin. Weld. Res. 70 (1991): p. 321s.
13. D.A. Jones, Principles and Prevention of Corrosion, 2nd ed. (Upper Saddle River, NJ: Prentice-Hall, 1996). p. 572.
14. R.D. Kane, J.P. Ribble, M.J. Schofield, Weld. J. 70 (1991): p. 56.
15. 2S Service." CORROSION/99, paper no. 421 (Houston, TX: NACE, 1999).
16. S.Y. Tsai, H.C. Shih, Corros. Sci. 38, 5 (1996): p. 705.
17. C.D. Kim, B.E. Wilde, "A Review of the Strain-Rate Stress Corrosion Cracking Test, "Stress Corrosion Cracking-The Slow Strain-Rate Technique, in ASTM STP 665, eds. G.M. Ugiansky, J.H. Payer (West Conshohocken, PA: ASTM International, 1979), p. 97.
18. H. Asahl, M. Ueno, T. Yonezawa, Corrosion 50, 7 (1994): p. 537.