Revised characterization of the controlled clearance piston gauge

Review of Scientific Instruments

Volumn 74, Issue 5, 2003, Pages 2899-2910

  Newhall, D H ^a   Newhall, W C ^a   Malloy, B T ^a  

^a Harwood Engineering Company   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

ELASTICITY; ENGINE CYLINDERS; EXTRAPOLATION; FLOW OF FLUIDS; HIGH PRESSURE EFFECTS; LOADS (FORCES); PRESSURE GAGES;

PISTON GAUGES; PRESSURE TRANSMISSIBILITY;

ENGINE PISTONS;

EID: 0037850987     PISSN: 00346748     EISSN: None     Source Type: Journal    
DOI: 10.1063/1.1569399     Document Type: Article

References (23)

1. P. L. M. Heydemann and B. E. Welch, Chapter 4, Part 3. Piston Gauges Reprinted from Experimental Thermodynamics, Volume II Experimental Thermodynamics of Non-Reacting Fluids, edited by B. Le Neindre and B. Vodar: Pure and Applied Chemistry: International Union of Pure and Applied Chemistry (Butterworths, London, 1975).
2. P. W. Bridgman, Proceedings of the American Academy of Arts and Science, 1912, Vol. 47, p. 321.
3. D. P. Johnson and D. H. Newhall, Trans. ASME 75, 301 (1953).
4. D. H. Newhall, L. H. Abbot, and R. A. Dunn, High Pressure Measurement, edited by A. A. Giardini, and E. C. Lloyd (Butterworths, Washington, 1963), pp. 339-354.
5. Committee Report (1971). Proceedings of a Symposium held at the National Bureau of Standards, Gaithersburg, MD, 1968, NBS Special Publication 326,313.
6. D. H. Newhall, I. Ogawa, and V. Zilberstein, Rev. Sci. Instrum. 50, 964 (1979).
7. J. K. N. Sharma, K. K. Jain, V. E. Bean, B. E. Welch, and R. J. Lazos, Rev. Sci. Instrum. 55, 563 (1984).
8. P. Radowski et al., Thick-Walled Cylinder Handbook (Watertown Arsenal, WA No. 893/172, December 1954). Surface Strains for Semi-Infinite Pressure.
9. V. E. Bean et al., Another Step Toward an International Pressure Scale, 2nd Airapt IPPS Task Group: Physics 139 & 140B (North Holland, Amsterdam, 1986), pp. 52-54.
10. G. F. Molinar, V. E. Bean, J. Houck, and B. Welch, Pressure Measurements with the Mercury Melting Line Referred to ITS-90 Metrologia 28, 353 (1991).
11. S. J. Kline and F. A. McClintock, Mech. Eng. (Am. Soc. Mech. Eng.) 3 (1953).
12. S. Yamamoto, A. Ooiwa, and M. Ueki, A Dead-Weight Piston Manometer as the National Primary Standard, Japanese Bureau of Standards, the 3rd Department, April 1985.
13. P. L. M. Heydemann, J. Appl. Phys. 38, 2640 (1967).
14. D. P. Johnson and P. L. M. Heydemann, J. Appl. Phys. 38, 1294 (1967).
15. A. E. Eremeev, Izmer. Tekh. 17, 19 (1974).
16. H. Niesler, I. Jackson, and E. C. Morris, High Tlemp.-High Press. 20, 995 (1988).
17. S. S. Sekoyan, G. K. Strelichev, and Yu. I. Shmin, Izmer. Tekh. 32, 31 (1989).
18. I. C. Getting, Metrologia 35, 119 (1998).
19. J. Krim, Sci. Am. 74 (1996).
20. J. P. Holman, Experimental Methods for Engineers (McGraw-Hill, New York, 1978).
21. J. L. Cross, NBS Monograph 65: Reduction of Data for Piston Gauge Pressure Measurements, U.S. Department of Commerce National Bureau of Standards, June 1963.
22. D. L. Decker, W. A. Bassett, L. Merrill, H. T. Hall, and J. D. Barnett, High Pressure Calibration-A Critical Review, High Pressure Data Center 1972.
23. P. Vergne, Candidate Fluids for High Pressure Standards: State Of The Art And Possible Trends: Laboratoire De Mecanique Des Contacts, URA CNRS 856, INSA Bâtment 118 20 Avenue Albert Einstein 69621 Villeurbanne Cedex-France.