High stress abrasive wear behavior of sillimanite-reinforced Al-alloy matrix composite: A factorial design approach

Journal of Materials Engineering and Performance

Volumn 12, Issue 3, 2003, Pages 331-338

  Singh, M ^a   Mondal, D P ^a   Jha, A K ^a   Yegneswaran, A H ^a  

^a REGIONAL RESEARCH LABORATORY CSIR   (India)

Author keywords

Aluminum matrix composite; Factorial design; Natural mineral; Sillimanite particles; Two body abrasive wear

Indexed keywords

ALUMINUM ALLOYS; REINFORCEMENT; SOLIDIFICATION; STRESS ANALYSIS; WEAR OF MATERIALS;

FACTORIAL DESIGN;

METALLIC MATRIX COMPOSITES;

EID: 0037804116     PISSN: 10599495     EISSN: None     Source Type: Journal    
DOI: 10.1361/105994903770343196     Document Type: Article

References (31)

1. A.I. Nussbaum: "New Application for Aluminium Based Metal Matrix Composites," Light Metal Age, 1997, pp. 54-58.
2. R. Chen, A. Iwabuchi, T. Shimizu, H.S. Stain, and H. Mifune: "The Sliding Wear Resistance Behaviour of NiAl and Sic Particles Reinforced Aluminium Alloy Matrix Composites," Wear, 1997, 213, pp. 175-84.
3. D.M. Schuster, M. Skibo, and F. Yep: "SiC Particles Reinforced Aluminium by Casting," J. Metal, 1987, 39, p. 60.
4. A.T. Alpas and J.D. Emburry: "Sliding and Abrasive Wear Behaviour of an Aluminium (2014) SiC Particle Reinforced Composite," Sci.Metall., 1990, 24, pp. 931-35.
5. A. Sato and R. Mehrabian: "Aluminium Matrix Composite Fabrication and Properties," Metall. Trans., 1976, 7(B), pp. 443-51.
6. P.M. Hosking, F.F. Portillo, W. Wunderlin, and R. Mehrabian: "Composite of Aluminium Alloys," J. Mater Sci, 1982, 17, pp. 477-98.
7. K.J. Bhansali and R. Meharabian: "Abrasive Wear of Aluminium-Matrix Composite," J. Metall. 1982, 34(9), pp. 30-34.
8. M.K. Surappa, S.V. Prasad, and R.K. Rohatgi: "Wear and Abrasion of Cast Al-Alumina Particle Composite," Wear, 1982, 77, pp. 295-302.
9. S.V. Prasad and P.K. Rotargi: "Mechanism of Material Removal During Low Stress and High Stress Abrasion of Aluminium Alloy Zircon Particles Composite," Mater. Sci. Eng., 1986, 80, pp. 213-20.
10. W.P. Caley, G.H. Kipouros, and P.W. Kingston: "The Potential Application of Natural Minerals Industries Minerals," CIM Bulletin, 1993, 85(968), pp. 116-21.
11. A.K. Jha, T.K. Dan, S.V. Prasad, and P.K. Rohatgi: "Alluminium Alloy-Solid Lubricant Talc Particle Composite," J. Mater, Sci., 1986, 21, pp. 3681-85.
12. J. Yang and D.D.L. Chung: "Wear of Bauxite Particles-Reinforced Aluminium Alloys," Wear, 1989, 135, pp. 53-65.
13. K. Anand and Kishor: "On the Wear of Aluminium-Corundum Composite," Wear, 1983, 85, pp. 163-69.
14. M. Singh, O.P. Modi, R. Dasgupta, and A.K. Jha: "High Stress Abrasive Wear Behaviour of Aluminium Alloy Granite Particle Composite," Wear, 1999, 233-235, pp. 455-61.
15. 3 Particle Composite: A Study on the Combined Effect of Load and Size of Abrasive," Wear, 1998, 223, pp. 131-38.
16. S. Das, S. Gupta, D.P. Mondal and B.K. Prasad: "Influence of Load and Abrasive Size on the Abrasive Wear of Al-SiC Composites," Aluminium Trans. 2000, 2(1), pp. 27-36.
17. L.J. Badse: "Influence of Grit Size on the Groove Formation During Sliding Abrasion," Wear, 1968, 11, p. 213.
18. E. Rabinowicz and A. Mutis: "Effect of Abrasive Particle Size on Wear," Wear, 1965, 18, p. 381.
19. M.A. Moore and R.M. Douthwaite: "Plastic Deformation Below Worn Surfaces," Metall. Trans., 1976, 7A, pp. 1833-39.
20. A.T. Alpas and J.D. Embury: "Wear Mechanisms in Laminated and Particle Reinforced Metal Matrix Composites" in Wear of Materials, Vol. 1, K.C. Ludema and R.G. Bayer, ed. ASME, New York, NY, 1991, pp. 159-66.
21. S. Datta: "Application of Design of Experiment on Electrophoretic Deposition of Glass Ceramic Coating Materials From an Aqueous Bath," Bull. Mater. Sci., 2000, 23(2), pp. 125-29.
22. R.J. Singh, S.N. Asthana, R. Ganguly, and B.K. Dhindaw: "Application of Design of Experiments to the Quantitative Study of the Strengthening Characteristics of Cast Al-Si-Mn-Mg Alloys," Trans. Indian Inst. Met., 1989, 42, pp. 307-15.
23. P.K. Rohatgi, R. Asthana, and S. Das: "Solidification Structures and Properties of Cast Metal Ceramic Particle Composites," Int. Met. Rev., 3(3), 1986, p. 115.
24. T. Kullik, T.H. Kosel, and Y. Xu: "Effect of Depth of Cut of Two Phase Alloys" in Proc. Int. Conf. Wear Mater. Vol. I, K.C. Luderna, ed., Denver, CO, 1989, pp. 23-33.
25. M.J. Murray, P.J. Mutton, and J.D. Watson: "Abrasive Wear Mechanisms in Steels." J. Lubr. Technol., Trans. ASME Trib., 1982, 104, pp. 9-15.
26. R.L. Deuis, C. Subramanian, and J.M. Yellup: "Abrasive Wear of Aluminium Composites - A Review," Wear, 1996, 201, pp. 132-44.
27. B.K. Prasad, A.K. Jha, O.P. Modi, S. Das, and A.H. Yegneswaran: "Abrasive Wear Characteristics of Zn-37.2 Al-2.5 Cu-0.2 Mg Alloy Dispersed With Silicon Carbide Particles," Mater, Trans. JIM, 1995, 38, pp. 1048-57.
28. T.H. Kosel and N.F. Fiore: "Abrasive Wear in Multiphase Microstructures," J. Mater. Energy Sys., 1981, 3, pp. 7-21.
29. A. Misra and I. Finnie: "On the Size Effect in Abrasive and Erosive Wear," Wear, 1980, 65, pp. 359-74.
30. T. Hisakado, H. Huda, and T. Trukui: "Effects of Dislodgment and Size of Abrasive Grains on Abrasive Wear," Wear, 1992, 155, pp. 297-307.
31. A.P. Mercer and I.M. Hutchings: "The Deterioration of Bonded Abrasive Papers During the Wear of Metals," Wear, 1989, 132, pp. 77-97.