Influence of pre- and post-heat treatment of anode substrates on the properties of DC-sputtered YSZ electrolyte films

Solid State Ionics

Volumn 159, Issue 1-2, 2003, Pages 1-8

  Wanzenberg, E ^a   Tietz, F ^a   Panjan, P ^b   Stover D ^a  

^a FORSCHUNGSZENTRUM JÜLICH   (Germany)

^b JO EF STEFAN INSTITUTE   (Slovenia)

Author keywords

Gas leakage; Microstructure; Sintering; SOFC; YSZ electrolyte

Indexed keywords

ANNEALING; ANODES; ELECTRIC CONDUCTIVITY; GASES; IMAGE ANALYSIS; MICROSTRUCTURE; POROSITY; SINTERING; SOLID OXIDE FUEL CELLS; SPUTTERING; YTTRIUM COMPOUNDS; ZIRCON;

GAS LEAKAGE;

DIELECTRIC FILMS;

EID: 0037338770     PISSN: 01672738     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0167-2738(02)00922-0     Document Type: Article

References (14)

1. Simwonis D., Thülen H., Dias F.J., Naoumidis A., Stöver D. J. Mater. Process. Technol. 92-93:1999;107.
2. Steele B.C.H. Bossel U. Proc. 1st Eur. SOFC Forum. Eur. Fuel Cell Forum, Oberrohrdorf, Switzerland. 1994;375.
3. Buchkremer H.P., Diekmann U., de Haart L.G.J., Kabs H., Stimming U., Stöver D. Stimming U., Singhal S.C., Tagawa H., Lehnert W. Proc. 5th Int. Symp. SOFC. 1997;160 The Electrochemical Society, Pennington, NJ, USA.
4. Will J., Mittendorfer A., Kleinlogel C., Perednis D., Gauckler L.J. Solid State Ionics. 131:2000;79.
5. Skrivasatva P.K., Quach T., Duan Y.Y., Donelson R., Jiang S.P., Ciacchi F.T., Badwal S.P.S. Thorstensen B. Proc. 2nd Eur. SOFC Forum. Eur. Fuel Cell Forum, Oberrohrdorf, Switzerland. 1996;761.
6. Hobein B., Tietz F., Stöver D., Čekada M., Panjan P. J. Eur. Ceram. Soc. 21:2001;1843.
7. Buchkremer H.P., Diekmann U., Stöver D. Thorstensen B. Proc. 2nd Eur. SOFC Forum. Eur. Fuel Cell Forum, Oberrohrdorf, Switzerland. 1996;221.
8. D. Simwonis, Optimierung von Anoden der Hochtemperatur-Brennstoffzelle durch Korrelation von Herstellungsverfahren, Gefüge und Eigenschaften, Reports of Forschungszentrum Jülich, Jül-3678, PhD thesis, Univ. Bochum. (1999).
9. Simwonis D., Tietz F., Stöver D. Solid State Ionics. 132:2000;241.
10. ASTM, Designation E 112-63, Book of ASTM Standards, Part 31, American Society for Testing Materials, Philadelphia.
11. German R.M. Sintering Theory and Practice. 1996;Wiley, New York, USA.
12. Dees D.W., Claar T.D., Easler T.E., Fee D.C., Mrazek F.C. J. Electrochem. Soc. 134:1987;2141.
13. Deprez N., McLachlan D.S., Sigalas I. Solid State Commun. 66:1988;869.
14. Powell R.W., Tye R.P., Hickman M.J. Int. J. Heat Mass Transfer. 8:1965;679.