Nonlinear numerical analysis in transient cutting tool temperatures

Journal of Manufacturing Science and Engineering, Transactions of the ASME

Volumn 125, Issue 1, 2003, Pages 48-56

  Jen, Tien Chien ^a   Eapen, Sunil ^a   Gutierrez, Gustavo ^b  

^a University of Wisconsin Milwaukee   (United States)

^b UNIVERSITY OF PUERTO RICO   (Puerto Rico)

Author keywords

[No Author keywords available]

Indexed keywords

ALGORITHMS; HEAT CONDUCTION; HEAT FLUX; MATHEMATICAL MODELS; OPTIMIZATION; PROBLEM SOLVING; TEMPERATURE DISTRIBUTION; THERMAL EFFECTS; THERMAL GRADIENTS;

CONTROL VOLUME APPROACH; TOOL CHIP INTERFACE;

CUTTING TOOLS;

EID: 0037306179     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.1536173     Document Type: Article

References (25)

1. Barrow, G., 1973, “A Review of Experimental and Theoretical Techniques for Assessing Cutting Temperatures,” CIRP Ann., 22, pp. 203-211.
2. Boothroyd, G., and Knight, W. A., 1989, Fundamentals of Machining and Machine Tools, Marcel and Dekker, New York, Chap. 3.
3. Chandra, A., and Chan, C. L., 1994, “Thermal Aspects of Machining: A BEM Approach,” Int. J. Solids Struct., 33, ppp. 1657-1693.
4. Shaw, M. C., 1984, Metal Cutting Principles, Oxford University Press, Oxford, Chap. 12.
5. Stephenson, D. A., 1991, “Assessment of Steady-State Metal Cutting Temperature Models Based on Simultaneous Infrared and Thermocouple Data,” ASME J. Eng. Ind., 113, pp. 121-128.
6. Strenkowski, J. S., and Moon, K. J., 1990, “Finite Element Prediction of Chip Geometry and Tool/Workpiece Temperature Distribution in Orthogonal Machining,” ASME J. Eng. Ind., 112, pp. 313-318.
7. Trigger, K. J., and Chao, B. T., 1951, “An Analytical Evaluation of Metal Cutting Temperatures,” Trans. ASME, 73, pp. 57-68.
8. Jen, T. C., and Anagonye, A. U., 2001, “An Improved Transient Model of Tool Temperature in Metal Cutting,” ASME J. Manuf. Sci. Eng., 123, pp. 30-37.
9. Radulescu, R., and Kapor, S. G., 1994, “An Analytical Model for Prediction of Tool Temperature Fields during Continuous and Interrupted Cutting,” ASME J. Eng. Ind., 116, pp. 135-143.
10. Stephenson, D. A., and Ali, A., 1992, “Tool Temperature in Interrupted Metal Cutting,” ASME J. Eng. Ind., 115, pp. 432-437.
11. Stephenson, D. A., Jen, T. C., and Lavine, A. S., 1997, “Cutting Tool Temperatures in Contour Turning: Transient Analysis and Experimental Verification,” ASME J. Manuf. Sci. Eng., 119, pp. 494-501.
12. Jen, T. C., and Gutierrez, G., 1999, “Finite Element Analysis in Transient Tool Temperatures,” National Heat Transfer Conference, Albuquerque, New Mexico.
13. Tay, A. O., Stevenson, M. G., and Vahl Davis, G., 1973, “Using the Finite Element Method to Determine Temperature Distributions in Orthogonal Machining,” Proc. Inst. Mech. Eng., 118, pp. 627-638.
14. Maekawa, K., Nakano, Y., and Kitawa, T., 1996, “Finite Element Analysis of Thermal Behavior in Metal Machining,” Jpn. Soc. Mech. Eng., 62, No. 596, pp. 1587-1593.
15. Jen, T. C., and Lavine, A. S., 1994, “Prediction of Tool Temperatures in Interrupted Metal Cutting,” Proceedings of the 7th International Symposium on Transport Phenomena in Manufacturing Processes, pp. 211-216.
16. Chao, B. T., and Trigger, K. J., 1955, “Temperature Distribution at the Tool-Chip Interface in Metal Cutting,” Trans. ASME, 77, pp. 1107-1121.
17. Levy, E. K., Tsai, C. L., and Groover, M. P., 1976, “Analytical Investigation of the Effect of Tool Wear on the Temperature Variations in a Metal Cutting Tool,” ASME J. Eng. Ind., February, pp. 251-257.
18. Tsai, C. L., 1973, “Finite Difference Solutions for the Time Dependent Temperature Distributions in Metal Cutting Tool,” MS thesis, Department of Mechanical Engineering and Mechanics, Lehigh University.
19. Incropera, F. P., and DeWitt, D. P., 1996, Introduction to Heat Transfer, John Wiley & Sons, New York.
20. Jen, T. C., and Gutierrez, G., 2000, “Numerical Heat Transfer Analysis in Transient Tool Temperatures,” National Heat Transfer Conference, Pittsburgh, Pennsylvania.
21. Van der Vorst, H. A., and Sonneveld, P, 1990, CGSTAB, A More Smoothly Converging Variant of CGS, Tech. report 90-50, Delf University of Technology.
22. Glub, G. H., and van Loan, C., 1990, Matrix Computations, Johns Hopkins University Press, Baltimore.
23. Ferzeiger, J. H., and Peric, M., 1997, Computational Methods for Fluid Dynamics, Springer-Verlag, Berlin, Heidelberg.
24. Eapen, S., 2000, “Numerical Heat Transfer Analysis in Three Dimensional Transient Cutting Tool Temperatures,” MS thesis, University of Wisconsin, Milwaukee.
25. Trent, E. M., 1977, Metal Cutting, Butterworths, Chapter 5.