Modeling and prediction of hole profile in drilling, Part 1: modeling drill dynamics in the presence of drill alignment errors

Journal of Manufacturing Science and Engineering

Volumn 125, Issue 1, 2003, Pages 6-13

  Gupta, Khagendra ^a   Ozdoganlar, O Burak ^a   Kapoor, Shiv G ^a   DeVor, Richard E ^a  

^a University of Illinois at Urbana Champaign   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTER SIMULATION; DYNAMICS; ERROR ANALYSIS; FORCE MEASUREMENT; VIBRATION MEASUREMENT; VIBRATIONS (MECHANICAL);

DRILL ALIGNMENT ERRORS; DRILL DYNAMICS; DYNAMIC DEFLECTION MODEL; EULER - BERNOULLI BEAM; HOLE PROFILE;

DRILLING;

EID: 0037304513     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1536932     Document Type: Article

References (21)

1. Watson, A. R., 1985, "Drilling Model for Cutting Lip and Chisel Edge and Comparison of Experimental and Predicted Results. I-Initial Cutting Lip Model," Int. J. Mach. Tool Des. Res., 25(4), pp. 347-365.
2. Watson, A. R., 1985, "Drilling Model for Cutting Lip and Chisel Edge and Comparison of Experimental and Predicted Results. II-Revised Cutting Lip Model," Int. J. Mach. Tool Des. Res., 25(4), pp. 367-376.
3. Watson, A. R., 1985, "Drilling Model for Cutting Lip and Chisel Edge and Comparison of Experimental and Predicted Results. III-Drilling Model for Chisel Edge," Int. J. Mach. Tool Des. Res., 25(4), pp. 377-392.
4. Watson, A. R., 1985, "Drilling Model for Cutting Lip and Chisel Edge and Comparison of Experimental and Predicted Results. IV-Drilling Tests to Determine Chisel Edge Contribution to Torque and Thrust," Int. J. Mach. Tool Des. Res., 25(4), pp. 393-404.
5. Chandrasekharam, V., Kapoor, S. G., and DeVor, R. E., 1998, "A Mechanistic Model to Predict the Cutting Force System for Arbitrary Drill Point Geometry," ASME J. Manuf. Sci. Eng., 120(3), pp. 563-570.
6. Sriram, R., 1996, "An Investigation of the Effect of Radial Forces in Drilling," Master's thesis, University of Illinois at Urbana-Champaign, Urbana-Illinois.
7. Fujii, H., Marui, E., and Ema, S., 1986, "Whirling Vibration in Drilling. Part 1: Cause of Vibration and Role of Chisel Edge," ASME J. Ind., 108, pp. 157-162.
8. Fujii, H., Marui, E., and Ema, S., 1986, "Whirling Vibration in Drilling. part 2: Influence of Drill Geometries, Particularly of the Drill Flank, on the Initiation of Vibration," ASME J. Ind., 108, pp. 163-168.
9. Fujii, H., Marui, E., and Ema, S., 1988, "Whirling Vibration in Drilling. Part 3: Vibration Analysis in Drilling Workpiece With a Pilot Hole," ASME J. Ind., 110, pp. 315-321.
10. Lin, C., Jalisi, M. N., and Ehmann, K. F., 1985, "Modeling and Experimental Analysis of Margin Forces in Micro-Drilling," ASME Manufacturing Processes and Materials Challenges in Microelectronic Packaging, AMD-Vol. 131/EEP-Vol. 1, pp. 25-33.
11. Chen, W. R., and Keer, L. M., 1993, "Transverse Vibrations of a Rotating Twisted Timoshenko Beam Under Axial Loading," ASME J. Vibr. Acoust., 115, pp. 285-294.
12. Tekinalp, O., and Ulsoy, A. G., 1989, "Modeling and Finite Element Analysis of Drill Bit Vibrations," ASME J. Vibr. Acoust., Stress, Reliab. Des. 111, pp. 148-155.
13. Rincon, D. M., and Ulsoy, A. G., 1995, "Complex Geometry, Rotary Inertia and Gyroscopic Effects on Drill Vibrations," J. Sound Vib., 188, pp. 701-715.
14. Lee, C. W., Katz, R., Ulsoy, A. G., and Scott, R. A., 1988, "Modal Analysis of Distributed Parameter Rotating Shaft," J. Sound Vib., 122, pp. 119-130.
15. Rincon, D. M., and Ulsoy, A. G., 1995, "Complex Geometry, Rotary Inertia, and Gyroscopic Moment Effects on Drill Vibrations," J. Sound Vib., 188(5), pp. 701-715.
16. Ulsoy, A. G., and Tekinalp, O., 1984, "Dynamic Modeling of Transverse Drill Bit Vibrations," CIRP Ann., 33(1), pp. 253-258.
17. Choi, S. H., Pierre, C., and Ulsoy, A. G., 1992, "Consistent Modeling of Rotating Timoshenko Shafts Subject to Axial Loads," ASME J. Vibr. Acoust., 114, pp. 249-259.
18. Lee, S. J., Eman, K. F., and Wu, S. M., 1987, "An Analysis of the Drill Wandering Motion," ASME J. Eng. Ind., 109, pp. 297-305.
19. Chiou, R. Y., and Wu, K., 1998, "Analysis of the Runout Effecton Hole Quality in Drilling," Proceedings of the ASME Manufacturing Science and Engineering Division, pp. 651-658.
20. Surendran, V., 1998, "A Study of Hole Quality in Drilling," Master's thesis, University of Illinois at Urbana-Champaign, Urbana-Illinois.
21. Meirovitch, L., 1997, Principles and Techniques of Vibrations, Prentice-Hall, Inc., Upper Saddle River, New Jersey 07458.