Strength prediction of weld-bonded joints

International Journal of Adhesion and Adhesives

Volumn 23, Issue 1, 2003, Pages 23-28

  Al Samhan, A ^a   Darwish, S M H ^a  

^a KING SAUD UNIVERSITY   (Saudi Arabia)

Author keywords

[No Author keywords available]

Indexed keywords

ADHESIVES; BOND STRENGTH (MATERIALS); BOUNDARY CONDITIONS; FINITE ELEMENT METHOD; SPOT WELDING; STRESS ANALYSIS;

ADHESIVE BONDED JOINTS;

WELDS;

EID: 0037278674     PISSN: 01437496     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0143-7496(02)00078-7     Document Type: Article

References (18)

1. Darwish S, Ghanya A. Critical assessment of weld-bonded technologies. J Mater Process Technol 2000; 221-229.
2. Heidi B, El-Sebakhy I, Malik D. Weldbonding of structural adhesives for body stiffening. Worldwide Passenger Car Conf., USA, 1992.
3. Masashi K.et al. Fatigue strength of adhesive bonded box section beams with a longitudinal partition under torsion. Trans Japan Soc Mech Eng A. 569:1993;87-93.
4. Wang PC, Chishholm, Banas G, Lawrence VL. The role of failure mode, resistance spot weld and adhesive on the fatigue behavior of weld-bonded aluminum. Weld J 1995; 41-47.
5. Darwish SM, Azaym K, Sadek MM. Dynamic characteristics of industrial double containment joints. Proceedings of the International Conference on CAPE, Edinburgh, 1989.
6. Darwish S.M., Azaym K., Sadek M.M. Design philosophy of a bonded gear box. Int J Mach Tools Manufact. 31:1991;625-631.
7. Darwish S.M., Niazi A., Ghanya A., Kassem M.E. Improving electrical conductivity of structural epoxy resin adhesives. Int J Adhesion Adhesives. 11(1):1990;27-41.
8. Kilik S., Davies R., Darwish S.M. Thermal conductivity of epoxy resin adhesives. Int J Adhesion Adhesives. 19(4):1990;219-223.
9. Darwish S.M., Niazi A., Ghanya A. Phase stability of duralumin machined with bonded and brazed metal cutting tools. Int J Mach Tools Manufact. 32(4):1992;593-600.
10. Schwartz MM. Metals joining manual book. New York: McGraw-Hill, 1979. p. 1-32.
11. Darwish S.M., Davies R. Adhesive bonding of metal cutting tools. Int J Mach Tools Manufact. 29(1):1989;141-152.
12. Darwish S.M., Davies R. Investigation of heat flow through bonded and brazed metal cutting tools. Int J Mach Tools Manufact. 29(2):1989;229-237.
13. Khalil A.A., Davies Analysis of bonded double containment cantilever joints. Int J Adhesion Adhesives. 19(4):1990;219-223.
14. Alsamhan A, Pillinger I, Hartely P. The development of real time re-meshing technique for simulating cold-roll-forming using FE methods, submitted for publication.
15. Alsamhan A, Hartely P, Pillinger I. The computer simulation of cold-roll-forming using FE methods and applied real time re-meshing techniques, submitted for publication.
16. Alsamhan A, Hartely P, Pillinger I. Predicting the deformation between forming stands of cold-roll-forming process using FE methods, submitted for publication.
17. Darwish S., Al-Abbas R., Sadek M.M. Design rational of bonded, double containment joints with dissimilar materials. Int J Adhesion Adhesives. II(2):1991;65-70.
18. GID software copy writes of International Center For Numerical Methods In Engineering (CIMNE)- Edificio C-1, Campus Norte UPC, 08034 Barcelona-Spain.