Experimental and theoretical optimization of combustion chamber and fuel distribution for the low emission direct-injection diesel engine

Journal of Engineering for Gas Turbines and Power

Volumn 125, Issue 1, 2003, Pages 351-357

  Kidoguchi, Y ^a   Sanda, M ^a   Miwa, K ^a  

^a UNIVERSITY OF TOKUSHIMA   (Japan)

Author keywords

[No Author keywords available]

Indexed keywords

COMBUSTION; COMPUTATIONAL FLUID DYNAMICS; DIESEL ENGINES; FUEL INJECTION; MATHEMATICAL MODELS; NITROGEN OXIDES; OPTIMIZATION; PARTICULATE EMISSIONS; TURBULENCE;

DIRECT-ENGINE DIESEL ENGINES; FUEL DISTRIBUTION; SQUISH LIP;

COMBUSTION CHAMBERS;

EMISSION;

EID: 0037244774     PISSN: 07424795     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1501077     Document Type: Article

References (27)

1. Shundoh, S., Kakegawa, T., Tsujimura, K., and Kobayashi, S., 1991, " The Effect of Injection Parameters and Swirl on Diesel Combustion with High Pressure Fuel Injection," SAE Paper No. 910489.
2. Pierpont, D. A., and Reitz, R. D., 1995, "Effects of Injection Pressure and Nozzle Geometry on D.I. Diesel Emissions and Performance," SAE Paper No. 950604.
3. Nakakita, K., et al., 1994, "Optimization of Pilot Injection Pattern and Its Effect on Diesel Combustion with High-Pressure Injection," JSME Int. J. Ser. B. 37, pp. 966-973.
4. Middlemiss, I. D., 1978, "Characteristics of the Perkins 'Squish Lip' Direct Injection Combustion System," SAE Paper No. 780113.
5. Daisho, Y., et al., 1986, "Effects of Combustion Chamber Geometry in a Direct-Injection Diesel Engine," Trans. Jpn. Soc. Mech. Eng., Ser. B 52(479), pp. 2768-2773.
6. x Emissions by Active Turbulence Generated in the Late Combustion Stage in Diesel Engines - 2nd Report," Trans. Jpn. Soc. Mech. Eng., Ser. B 57 534), pp. 773-777.
7. Zhang, L., et al., 1996, "Effect of Chamber Geometry on Flame Behavior in a DI Diesel Engine," Trans. Jpn. Soc. Mech. Eng., Ser. B 62 600), pp. 3213-3219.
8. Sakata, K., et al., 1990, "Development of Toyota Reflex Burn (TRB) System in DI Diesel Engine," SAE Paper No. 900658.
9. Baert, R. S. G., Beckman, D. E., and Verbeek, R. P., 1996, "New EGR Technology Retains HD Diesel Economy with 21st Century Emissions," SAE Paper No. 960848.
10. x by Controlling Both the Turbulence and the Mixture Formation in DI Diesel Engines," SAE Paper No. 932797.
11. Shimazaki, N., et al., 1998, "Combustion and Emission Characteristics of Premixed Lean Diesel Combustion - Attempts to Control Ignition Timing of PREDIC with Several Kinds of Gas Added into Intake," Trans. JSAE. 29(3), pp. 61-65.
12. Matsui, Y., et al., 1997, "A New Combustion Concept for Small DI Diesel Engines - 1st Report: Introduction of the Basic Technology, Trans. JSAE 28(1), pp. 41-46.
13. Yanagihara, H., et al., 1997, "A Study of DI Diesel Combustion under Uniformly-Highly Dispersed Mixture Formation," Trans. JSAE 28(4), pp. 17-22.
14. Hashizume, T, et al., 1998. "Combustion and Emission Characteristics of Multiple Stage Diesel Combustion," SAE Paper No. 980505.
15. x and Particulate From a Direct-Injection Diesel Engine," SAE Paper No. 1999-01-1502.
16. Miwa, K., Ueta, T., and Ishiyama, T., 1991, "Effect of Swirl on Particulate Emissions from Direct- Injection Diesel Engines," Trans. Jpn. Soc. Mech. Eng. 57(538), pp. 2159-2165.
17. Ishiguro, J., Kidoguchi, Y., and Ikegami, M., 1998, " Three-Dimensional Simulation of the Diesel Combustion Process," JSME Int. J., Ser. II 31(1), pp. 158-165.
18. Ikegami, M., Hida, M., and Ishiguro, J., 1989, "Simulation of Flow and Combustion in Engine Combustion Chambers with Arbitrary Geometries," Trans. JSAE 42, pp. 33-37.
19. Ikegami, M., Kidoguchi, Y., and Nishiwaki, K., 1986, "A Multidimensional Model Prediction of Heat Transfer in Non-Fired Engines," SAE Paper No. 860467.
20. Magunussen, B. F., and Hjertager, B. H., 1976, "On Mathematical Modeling of Turbulent Combustion with Special Emphasis on Soot Formation and Combustion," 16th Symp. (Int.) on Combust., The Combustion Insitute, pp. 719-727.
21. Edelman, R. B., and Harsha, P. T., 1975, "Laminar and Turbulent Gas Dynamics in Combustors - Current Status," Prog. Energy Combust. Sci. 4, pp. 1-62.
22. Ikegami, M., Miwa, K., and Ikeda, H., 1974, "Analysis of the Diesel Combustion Process Based on Varying Delay Mechanism," Bull. JSME 17 114), pp. 1619-1628.
23. Ikegami, M., Nakatani, K., and Shioji, M., 1996, "Stochastic Model for Ignition of a Diesel Spray," The 34th Symp. on Combust., Combustion Society of Japan, pp. 286-288.
24. Ikegami, M., Miwa, K., and Li, X., 1986, "Spray Process and Pyrolysis in the Initial Stage of Diesel Combustion," Bull. JSME 29(253), pp. 2189-2195.
25. Wakuri, Y., et al., 1959, "Studies on the Penetration of Fuel Spray of Diesel Engine," Trans. Jpn. Soc. Mech. Eng. 25(156), pp. 820-826.
26. Yang, C., Kidoguchi, Y., and Miwa, K., 1999, "Effect of Rich and High Turbulence Combustion on Emissions and Flame Behavior in a Direct-Injection Diesel Engine," Trans. Jpn. Soc. Mech. Eng. 65 637), pp. 3203-3208.
27. Myerson, A. L., 1975, "The Reduction of Nitric Oxide in Simulated Combustion Effluents by Hydrocarbon-Oxygen Mixture," Combust. 15th Symp. (Int.) on Combust., Combust. Inst., pp. 1085-1092.