Development of chemically recuperated micro gas turbine

Journal of Engineering for Gas Turbines and Power

Volumn 125, Issue 1, 2003, Pages 391-397

  Nakagaki, T ^a   Ogawa, T ^a   Hirata, H ^a   Kawamoto, K ^a   Ohashi, Y ^a   Tanaka, K ^a  

^a TOSHIBA CORPORATION   (Japan)

Author keywords

[No Author keywords available]

Indexed keywords

EXHAUST GASES; LOW TEMPERATURE EFFECTS; METHANE; PARTICULATE EMISSIONS; STEAM; WASTE HEAT UTILIZATION;

CHEMICALLY RECUPERATED GAS TURBINE (CRGT) SYSTEM; METHANE STEAM; MICRO GAS TURBINES (MGT); THERMAL EFFICIENCY;

GAS TURBINES;

GAS TURBINE;

EID: 0037240822     PISSN: 07424795     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1520158     Document Type: Article

References (17)

1. Carapellucci, R., Risalvato, V., and Cau, G., 1994, " Characteristics of the Heat Recovery Methanol Reforming in CRGT Power Generation Systems," Proc., ASME COGEN-TURBO, IGTI-Vol. 9, ASME, New York, pp. 257-264.
2. Carapellucci, R., Risalvato, V., Bruno C., and Cau, G., 1996, "Performance and Emissions of CRGT Power Generation Systems With Reformed Methanol," Proc., IECEC 96, ASME, New York, 2, pp. 707-712.
3. Kuroda, K., Imai, T., and Yanagi, M., 1989, "Development of Methanol Reformer," Mitsubishi Jukou Gihou,26(5), pp. 408-412.
4. Nagaya, K., Oshiro, H., Ito, H., and Yoshino, N., 1993, " Demonstration Test of Reformed Methanol Gas-Turbine Power Generation,"Hitachi Zousen Gihou, 54(3), pp. 180-184.
5. Xu, J., and Froment, G. F., 1989, "Methane Steam Reforming, Methanation and Water-Gas Shift: I. Intrinsic Kinetics," AIChE J., 35(1), pp. 88-96.
6. Hyman, M. H., 1968, "Simulate Methane Reformer Reactions," Hydrocarbon Process.,47(7), pp. 131-137.
7. Murray, A. P., and Snyder, T. S., 1985, "Steam-Methane Reformer Kinetic Computer Model with Heat Transfer and Geometry Options," Ind. Eng. Chem. Process Des. Dev.,24, pp. 286-294.
8. Alafiqui, I. M., Meziou, A. M., and Gasmelseed, G. A., 1989, " Modeling, Simulation and Sensitivity Analysis of Steam-Methane Reformers," Int. J. Hydrogen Energy, 14(4), pp. 241-256.
9. Fukusako, S., Yamada, M., and Usami, Y., 1997, "Heat and Mass Transfer Characteristics in a Reforming Catalyst Bed," J. HTSJ,36(140), pp. 18-26.
10. Altman, D., and Wise, H., 1956, "Effect of Chemical Reactions in the Boundary Layer on Convective Heat Transfer," Jet Propul.,(4 , pp. 256-269.
11. Wijngaarden, R. J., and Westerterp, K. R., 1989, "Do the Effective Heat Conductivity and the Heat Transfer Coefficient at the Wall Inside a Packed Bed Depend on a Chemical Reaction? Weakness and Applicability of Current Models," Chem. Eng. Sci., 44(8), pp. 1653-1663.
12. Grover, S. S., 1970, Hydrocarbon Process.,49(4), pp. 109.
13. Nakagaki, T., Ogawa, T., Murata, K., and Nakata, Y., 2001, " Development of Methanol Steam Reformer for Chemical Recuperation," ASME J. Eng. Gas Turbines Power, 123, pp. 272-733.
14. Gnielinski, V., " Gleichungen zur Berechnung des Wärmeü bergangs in querdurchströmten cinzelnen Rohrreihen und Rohrbü ndeln," Forsch. Ingcnieurwes., 44, pp 15-25.
15. Yagi, S., and Kunii, D., 1962, " Studies on Heat Transfer in Packed Beds, " Int. Devel. Heat Transfer, Part IV, 750-759.
16. Zukauskas, A. A. Makarevičisu, V. J., and Slančiauskas, V. J., 1968, " Heat Transfer in Banks of Tubes in Crossflow of Fluid," Thermophy., 1, pp. 47-68.
17. Ergun, S;, 1952, " Fluid Flow Through Packed Columns," Chem. Eng. Prog., 48, pp. 89-94.