Analysis of EHL circular contact shut down

Journal of Tribology

Volumn 125, Issue 1, 2003, Pages 76-90

  Zhao, Jiaxin ^a   Sadeghi, Farshid ^a  

^a PURDUE UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

DECELERATION; DYNAMIC LOADS; FILMS; INTERFACES (MATERIALS); LUBRICANTS; PRESSURE; PRESSURE DISTRIBUTION; VELOCITY;

FILM THICKNESS;

ELASTOHYDRODYNAMIC LUBRICATION;

ELASTOHYDRODYNAMIC LUBRICATION; FILM THICKNESS; MATHEMATICAL ANALYSIS; MODEL; SURFACE CONTACT; VELOCITY;

EID: 0037226116     PISSN: 07424787     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1481366     Document Type: Article

References (26)

1. Gohar, R., and Cameron, A., 1963, "Optical Measurement of Oil Film Thickness Under EHD Lubrication," Nature (London), 200, pp. 458-459.
2. Koye, K. A., and Winer, W. O., 1981, "An Experimental Evaluation of the Hamrock and Dowson Minimum Film Thickness Equation for Fully Flooded EHD Point Contacts," ASME J. Lubr. Technol., 103, pp. 284-294.
3. Smeeth, M., and Spikes, H. A., 1997, "Central and Minimum Elastohydrodynamic Film Thickness at High Contact Pressure," ASME J. Tribol., 119, pp. 291-296.
4. Glovnea, R. P., and Spikes, H. A., 2001, "Elastohydrodynamic Film Collapse During Rapid Deceleration. Part I: Experimental Results," ASME J. Tribol., 123, pp. 254-261.
5. Hamrock, B. J., and Dowson, D., 1976, "Isothermal Elastohydrodynamic Lubrication of Point Contact: Part I-Theoretical Formulation," ASME J. Lubr. Technol., 98, pp. 223-229.
6. Hamrock, B. J., and Dowson, D., 1976, "Isothermal Elastohydrodynamic Lubrication of Point Contact: Part II-Ellipticity Parameter Results," ASME J. Lubr. Technol., 98, pp. 375-383.
7. Lubrecht, A. A., 1987, "Numerical Solution of the EHL Line and Point Contact Problem Using Mulligrid Techniques," Ph.D. thesis, University of Twente, Enschede, The Netherlands, ISBN 90-9001583-3.
8. Venner, C. H., 1991, "Multilevel Solution of the EHL Line and Point Contact Problems," Ph.D. thesis, "University of Twente, Enschede, The Netherlands, ISBN 90-9003974-0.
9. Venner, C. H., 1994, "Higher-Order Multilevel Solvers for the EHL Line and Point Contact Problems," ASME J. Tribol., 116, pp. 741-750.
10. Brandt, A., and Lubrecht, A. A., 1990, "Multilevel Matrix Multiplication and Fast Solution of Integral Equations," J. Comput. Phys., 90, pp. 348-370.
11. Stanley, H. M., and Kato, T., 1997, "An FFT-Based Method for Rough Surface Contact," ASME J. Tribol., 119, pp. 481-485.
12. Venner, C. H., and Lubrecht, A. A., 1994, "Numerical Simulation of a Transverse Ridge in a Circular EHL Contact Under Rolling/Sliding," ASME J. Tribol., 116, pp. 751-761.
13. Kaneta, M., Sakai, T., and Nishikawa, H., 1992, "Optical Interferometric Observations of the Effects of a Bump on Point Contact EHL," ASME J. Tribol., 114, pp. 779-784.
14. Kim, K., and Sadeghi, F., 1991, "Non-Newtonian Elastohydrodynamic Lubrication of Point Contact," ASME J. Tribol., 113, pp. 703-711.
15. Kim, K., and Sadeghi, F., 1993, "Three-Dimensional Temperature Distribution in EHD Lubrication: Part II-Point Contact and Numerical Formulation," ASME J. Tribol., 115, pp. 36-45.
16. Zhao, J., Sadeghi, F., and Hoeprich, M. H., 2001, "Analysis of EHL Circular Contact Start Up: Part I-Mixed Contact Model with Pressure and Film Thickness Results," ASME J. Tribol., 123, pp. 67-74.
17. Zhao, J., Sadeghi, F., and Hoeprich, M. H., 2001, "Analysis of EHL Circular Contact Start Up: Part II-Surface Temperature Rise Model and Results," ASME J. Tribol., 123, pp. 75-82.
18. Glovnea, R. P., and Spikes, H. A., 2001, "Elastohydrodynamic Film Formation at the Start-Up of the Motion," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 215, pp. 125-138.
19. Glovnea, R. P., and Spikes, H. A., 2000, "The Influence of Lubricant Upon EHD Film Behavior During Sudden Halting of Motion," Tribol. Trans., 43, pp. 731-739.
20. Sugimura, J., Jones, Jr., W. R., and Spikes, H. A., 1998, "EHD Film Thickness in Non-Steady State Contacts," ASME J. Tribol., 120, pp. 442-452.
21. Christensen, H., 1970, "Elastohydrodynamic Theory of Spherical Bodies in Normal Approach," ASME J. Lubr. Technol., 92, pp. 145-154.
22. Dowson, D., and Wang, D., 1994, "An Analysis of the Normal Bouncing of a Solid Elastic Ball on an Oily Plate," Wear, 179, pp. 29-37.
23. Larsson, R., and Höglund, E., 1995, "Numerical Simulation of a Ball Impacting and Rebounding a Lubricated Surface," ASME J. Tribol., 117, pp. 94-102.
24. Glovnea, R. P., and Spikes, H. A., 2001, "Elastohydrodynamic Film Collapse During Rapid Deceleration: Part II-Theoretical Analysis and Comparison of Theory and Experiment," ASME J. Tribol., 123, pp. 262-267.
25. Greenwood, J. A., and Morales-Espejel, G. E., 1994, "The Behaviour of Transverse Roughness in EHL Contacts," Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 208, pp. 121-132.
26. Strauss, W. A., 1992, Partial Differential Equations: An Introduction, John Wiley & Sons, New York.