The design of a high performance modular CNC system architecture

IEEE International Symposium on Intelligent Control - Proceedings

Volumn , Issue , 2002, Pages 290-296

  Ambra, Claudio ^a   Oldknow, Kevin ^a   Migliorini, Giuseppe ^a   Yellowley, Ian ^a  

^a NONE

Author keywords

Dynamic system reconfiguration; Extensible controls; FPGA based motion control; Open architecture CNC

Indexed keywords

ALGORITHMS; COMPUTER CONTROL SYSTEMS; COMPUTER SOFTWARE; FIELD PROGRAMMABLE GATE ARRAYS; MOTION CONTROL; NUMERICAL CONTROL SYSTEMS; PERSONAL COMPUTERS; POSITION MEASUREMENT;

DYNAMIC SYSTEM RECONFIGURATION; EXTENSIBLE CONTROLS; FIELD PROGRAMMABLE GATE ARRAY-BASED MOTION CONTROL; OPEN ARCHITECTURE COMPUTER NUMERICAL CONTROL SYSTEMS;

CONTROL SYSTEM SYNTHESIS;

EID: 0036907248     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (15)

1. G. Pritschow, C.H. Daniel, G. Junghans and W. Sperling, "Open system controllers - a challenge for the future of the machine tool industry", Annals of the CIRP, v. 42, n. 1, pp. 449-452, 1993
2. S. Schofield and P. Wright, "Open architecture controllers for machine tools, part 1: Design principles", ASME Journal of Manufacturing Science and Engineering, v. 120, pp. 417-424, 1998
3. Y. Altintas and W.K. Munasinghe, "A hierarchical open-architecture CNC system for machine tools", Annals of the CIRP, v. 43, n. 1, pp. 349-354, 1994
4. R.W. Teltz and M.A. Elbestawi, "Design basis and implementation of an open architecture machine tool controller", Transactions of NAMRI/SME, v. XXV, pp. 229-304, 1997
5. C.P. Bailo and C.J. Yen, "Open Modular Architecture Controls at GM Powertrain: Technology and Implementation", Proceedings of SPIE, v. 2912, pp. 52-63, 1991
6. P. Lutz and W. Sperling, "OSACA - the vendor neutral control architecture", Proceedings of the European Conference on Integration in Manufacturing, Dresden, Germany, 10 pp., 1997
7. C. Sawada and O. Akira, "Open Control Architecture OSEC-II: Architecture overview and prototype systems", IEEE Symposium on Emerging Technologies and Factory Automation, ETFA '97, Los Angeles, pp. 543-550, 1997
8. I. Yellowley and P.R. Pottier, "The Development of a Flexible Integrated Machine Controller", Atlantic Congress on Advanced Manufacturing, Halifax, September, 1991.
9. I. Yellowley and P.R. Pottier, "The integration of process and geometry within an open architecture machine tool controller", International Journal of Machine Tools & Manufacture, v. 34, n. 2, pp. 277-293, 1994
10. I. Yellowley, R. Ardekani, L. Yang and R. Seethaler, "Development of robust extensible architectures for machine tool control", Proceedings of SPIE, v. 2912, pp. 72-81, 1996
11. F.M. Proctor, W. Shackleford, C. Yang, T. Barbara, M.L. Fitzgerald, N. Frampton, K. Bradford and D. Koogle, "Simulation and Implementation of an Open Architecture Controller," Modeling, Simulation, and Control Technologies for Manufacturing, Proceedings of SPIE, v. 2596, October 1995
12. M. Albert, "Open-Architecture CNC Closes Servo Loop In Software", Modern Machine Shop, July, 1997
13. W.M. Bradley, D.M. Kahn, J. Rible and M. Williams, "IEEE Standard for Boot (Initialization Configuration) Firmware: Core Requirements and Practices - IEEE Std. 1275-1994", Institute of Electrical and Electronics Engineers, New York, 1994
14. B.Eckert, "Firmware Factory User's Manual", http://www.geocities.com/SiliconValley/Cable/3439, 1999
15. K.D. Oldknow and I. Yellowley, "The Design, Implementation and Validation of a System for the Dynamic Reconfiguration of Open Architecture Machine Tool Controls", International Journal of Machine Tools & Manufacture, v. 41, pp. 795-808, 2001