The effects of geometric parameters on the failure strength for pin-loaded multi-directional fiber-glass reinforced epoxy laminate

Composites Part B: Engineering

Volumn 33, Issue 8, 2002, Pages 567-578

  Okutan, Buket ^a  

^a DOKUZ EYLUL UNIVERSITY   (Turkey)

Author keywords

A. Glass fibers; Non linear behavior; Pin; Strength; Stress strain curves

Indexed keywords

FAILURE ANALYSIS; GLASS FIBERS; JOINTS (STRUCTURAL COMPONENTS); LAMINATED COMPOSITES; STRAIN; STRENGTH OF MATERIALS; STRESSES;

EPOXY LAMINATES;

FIBER REINFORCED MATERIALS;

EID: 0036892301     PISSN: 13598368     EISSN: None     Source Type: Journal    
DOI: 10.1016/S1359-8368(02)00054-9     Document Type: Article

References (30)

1. De Jong T. Stresses around pin-loaded holes in elastically orthotropic or isotropic plates. J Compos Mater. 11:1977;313-331.
2. Lekhnitskii S.G. Anisotropic plates. 1998;Gordon and Breach, London.
3. Waszczak J.P., Cruse T.A. Failure mode and strength predictions of anisotropic bolt bearing specimens. J Compos Mater. 5:1971;421-425.
4. Matthews F.L., Wong C.M., Chryssafitis S. Stress distribution around a single bolt in fiber-reinforced plastic. Composites. July:1982;316-322.
5. Chang F.K., Scott R.A., Springer G.S. Strength of mechanically fastened composite joints. J Compos Mater. 16:1982;470-494.
6. Chang F.K. The effect of pin load distribution on the strength of pin loaded holes in laminated composites. J Compos Mater. 20:1986;401-408.
7. Lin C.C., Lin C.H. Stresses around pin-loaded hole in composite laminates using direct boundary element method. Int J Solids Struct. 36:1999;763-783.
8. Lessard L.B., Shokrieh M.M. Two-dimensional modeling of composite pinned-joint failure. J Compos Mater. 29:1995;671-697.
9. Camanho P.P., Matthews F.L. A progressive damage model for mechanically fastened joints in composite laminates. J Compos Mater. 33:1999;2248-2280.
10. Hassani F., Shokrieh M.M., Lessard L.B. A fully non-linear 3D constitutive relationship for the stress analysis of a pin-loaded composite laminate. Compos Sci Technol. 62:2002;429-439.
11. Sun H.T., Chang F.K., Qing X. The response of composite joints with bolt-clamping loads. Part I. Model development. J Compos Mater. 1:2002;47-92.
12. Iarve E. Three-dimensional stress analysis in laminated composites with fasteners based on the B-spline approximation. Composites, Part A. 28A:1997;559-572.
13. Camanho P.P., Matthews F.L. Delamination onset prediction in mechanically fastened joints in composite laminates. J Compos Mater. 10:1999;906-927.
14. Li H.-C., Chang F.K. Strength envelope of bolted composite joints under bypass loads. J Compos Mater. 30:1996;1402-1434.
15. Collings T.A. The strength of bolted joints in multi-directional CFRP laminates. Composites. 1977;43-55.
16. Hart-Smith L.J. Mechanically fastened joints for advanced composites - phenomelogical considerations and simple analysis. Leneo E.M., Oplinger D.W., Burke J.J. Fibrous composites in structural design. 1980;Plenum Press, New York.
17. Chen J.C., Lu C.K., Chiu C.H., Chin H. On the influence of weave structure on pin-loaded strength of orthogonal 3D composites. Composites. 25:1994;251-262.
18. Abd-El-Naby S.F.M., Hollaway L. The experimental behaviour of bolted joints in pultruded glass/polyester material. Part 1. Single-bolt joints. J Compos Mater. 24:1993;531-538.
19. Quinn W.J., Matthews F.L. The effect of stacking sequence on the pin-bearing strength in glass fiber reinforced plastic. J Compos Mater. 11:1977;139-145.
20. Maikuma H., Kubomura K. Bearing strength and damage progress for PAN-based and pitch-based carbon fiber composites. J Compos Mater. 27:1993;1739-1761.
21. ASTM 3039-76, Test method for tensile properties of fiber-resin composites. 1982;American Society for Testing of Materials.
22. Test method for shear properties of composite materials by the V-notched beam method. 1996;American Society for Testing of Materials.
23. Tsai H.H., Morton M.Y., Farley G.L. An experimental investigation of Iosipescu specimen for composite materials. J Exp Mech. 1991;328-336.
24. Hahn H.T. Nonlinear behavior of laminated composites. J Compos Mater. 7:1973;257-271.
25. ASTM D 3518-76, In-plane shear stress-strain response of unidirectional reinforced plastics. 1982;American Society for Testing of Materials.
26. Jones R.M. Mechanics of composite materials. 1998;McGraw-Hill, Tokyo.
27. Okutan B., Aslan Z., Karakuzu R. A study of the effects of various geometric parameters on the failure strength of pin-loaded woven-glass-fiber reinforced epoxy laminate. Compos Sci Technol. 61:2001;1491-1497.
28. Okutan B. Stress and failure analysis of laminated composite pinned joints. PhD Thesis. Izmir (Turkey): Department of Mechanical engineering, Dokuz Eylul University; December 2001.
29. Aktaş A., Karakuzu R. Failure analysis of two dimensional carbon-epoxy composite plate pinned joint. Mech Compos Mater Struct. 6:1999;347-361.
30. Hashin Z. Failure criteria for unidirectional fiber composites. J Appl Mech. 47:1980;329-334.