Machining quality and cost: Estimation and tradeoffs

Journal of Manufacturing Science and Engineering

Volumn 124, Issue 4, 2002, Pages 840-851

  Nicolaou, Panicos ^a   Thurston, Deborah L ^a   Carnahan, James V ^a  

^a University of Illinois at Urbana Champaign   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

DECISION MAKING; MATHEMATICAL MODELS; QUALITY CONTROL; STATISTICAL METHODS; STOICHIOMETRY;

MILLING QUALITY ESTIMATION MODELS;

MACHINING;

EID: 0036851753     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1511169     Document Type: Article

References (28)

1. Chen, W., Wiecek, M., and Zhang, J., 1998, "Quality Utility - A Compromise Programming Approach to Robust Design," Proc. ASME Design Automation Conference, Atlanta, Georgia.
2. Ashby, F., and Esawl, A., 1999, "Cost Estimating for Process Selection," Proc. ASME Design for Manufacturing Conference, Las Vegas, Nevada.
3. Xirouchakis, P., and Kiritsis, D., 1998, "An Incremental Part Manufacturing Cost Estimation Algorithm Using Petri Nets," Proc. ASME Design for Manufacturing Conference, Atlanta, Georgia.
4. Thornton, A., 1997, "Using Key Characteristics to Balance Cost and Quality During Product Development," Proc. ASME Design Theory and Methodology Conference, Sacramento, California.
5. Wu, C., Chen, Z., and Tang, C., 1998, "Component Tolerance Design for Minimum Quality Loss and Manufacturing Cost," Computers in Industry, 35, pp. 223-232.
6. Cozzens, D.A., Rao, P.D., Olson, W.W., Sutherland, J.W., and Panetta, J.M., 1999, "An Experimental Investigation into the Effect of Cutting Fluid Conditions on the Boring of Aluminum Alloys," ASME J. Manuf. Sci. Eng., 121(3), pp. 434-439.
7. Locascio, A., and Thurston, D., 1998, "Transforming the House of Quality to a Multiobjective Optimization Formulation," Struct. Optim., 16(2), pp. 136-146.
8. Urlichs, R., 1999, "A Predictive Quality Model in a Design for Machining Decision Tool with Consideration of Uncertainty," Thesis, University of Illinois at Urbana-Champaign.
9. Walsh, R., 1999, McGraw-Hill Machining and Metalworking Handbook, McGraw-Hill, New York.
10. Surendran, V., 1998, "A Study of Hole Quality in Drilling," Master's thesis, University of Illinois at Urbana-Champaign.
11. Cooper, R., and Kaplan, R.S., 1991, "Profit Priorities from Activities Based Costing," Harvard Bus. Rev., May-June, 130-135.
12. Schreiner, T., 1999, "Cost Estimation for Tradeoff Decisions in Design for Manufacturing," Thesis, University of Illinois at Urbana-Champaign.
13. Bidanda, B., Kadilal, M., and Billo, R.E., 1998, "Development of an Intelligent Castability and Cost Estimation System," Int. J. Prod. Res., 36, pp. 547-568.
14. Kalpakjian, S., 1995, Manufacturing Engineering and Technology, Third Edition, Addison-Wesley.
15. nd edition.
16. Berry, M., 2000, "A Machining and Cutting Fluid Decision Tool for Cost, Quality and Environmental Tradeoffs," Master's thesis, University of Illinois at Urbana-Champaign.
17. Skerlos, S.J., DeVor, R.E., and S.G. Kapoor, 1998, "Environmentally Conscious Disposal Considerations in Cutting Fluid Selection," IMEC-E-Proceedings of ASME.
18. Childers, J.C., 1994, "The Chemistry of Metalworking Fluids," Metalworking Fluids, Marcel-Dekker, New York, pp. 165-189.
19. U.S. Environmental Protection Agency, 1983b, "Treatability Manual: Technology for Control/Removal of Pollutants," Washington DC, Office of Research and Development, Publication No EPA-600/2-82-001c.
20. U.S. Environmental Protection Agency, 1983a, "Treatability Manual: Cost Estimating," Washington DC, Office of Research and Development, Publication No EPA-600/2-82-001d.
21. U.S. Environmental Protection Agency, 1995, "Development Document for the Proposed Effluent Limitations Guidelines and Standards for the Metal Products and Machinery Phase I Source Category," Springfield VA, U.S. Department of Commerce, Publication No 821-R-95-021.
22. Wright, D.G., and Woods, D.R., 1993, "Evaluation of Capital Cost Data. Part 7: Liquid Waste Disposal with Emphasis on Physical Treatment," Can. J. Chem. Eng., 71, pp. 575-590.
23. Thurston, D., and Tiefu, Liu, 1991, "Design Evaluation of Multiple Attributes under Uncertainty," Int. J. Syst. Autom.: Res. Appl., 1(2), pp. 143-159.
24. Thurston, D.L., Carnahan, J.V., and Liu, T., 1994, "Optimization of Design Utility," ASME J. Mech. Des., 116(3), pp. 801-808.
25. Thurston, D.L., 2001, "Real and Perceived Limitations to Decision Based Design with Utility Analysis," ASME J. Mech. Des., 123(2), pp. 176-182.
26. Tian, Y.Q., Thurston, D.L., and Carnahan, J.V., 1994, "Incorporating End-users' Attitudes Towards Uncertainty into an Expert System," ASME J. Mech. Des., 116(2), pp. 493-500.
27. Thurston, D., 1991, "A Formal Method for Subjective Design Evaluation with Multiple Attributes," Res. Eng. Des., 3(2), pp. 105-122.
28. Keeney, R., and Raiffa, H., 1993, Decisions with Multiple Objectives, Cambridge University Press.