Rapid determination of the fracture toughness of metallic materials using circumferentially notched bars

Journal of Materials Engineering and Performance

Volumn 11, Issue 5, 2002, Pages 571-576

  Bayram, Ali ^a   Uguz, Agah ^a   Durmus, Ali ^a  

^a ULUDAG UNIVERSITY   (Turkey)

Author keywords

Al Si cast alloys; Al Zn Mg Cu wrought alloy; Dual phase steel; Fracture toughness

Indexed keywords

FRACTURE TOUGHNESS; HEAT TREATMENT; MORPHOLOGY; NOTCHED BAR TENSILE TESTING; SILICON; STEEL; STRESS CONCENTRATION;

DUAL PHASE STEEL; FRACTURE TOUGHNESS TESTS;

ALUMINUM ALLOYS;

EID: 0036810727     PISSN: 10599495     EISSN: None     Source Type: Journal    
DOI: 10.1361/105994902770343836     Document Type: Article

References (19)

1. Anon: "ASTM Designation E399, Standard Test Method for Plane-Strain Fracture Toughness of Metallic Materials" in Annual Book of ASTM Standards, Part 3, American Society for Testing and Materials, Philadelphia, PA, 1988, pp. 680-715.
2. Anon: "BSI Standard BS5762" in Methods for Crack Opening Displacement (COD) Testing, British Standards Institution, London, UK, 1979, pp. 1-14.
3. Anon: "ASTM Designation E399, Standard Test Method for Crack-Tip Opening Displacement (CTOD) Fracture Toughness Measurement" in Annual Book of ASTM Standards, Part 3, American Society for Testing and Materials, Philadelphia, PA, 1993, pp. 952-61.
4. S. Kang and N.J. Grant: "Notch Tensile Testing as a Measure of the Toughness of Aluminum Alloys," Mat. Sci. Eng., 1985, 72, pp. 155-62.
5. B. Ule, B. Leskocsek, and B. Tuma: "Estimation of Plane Strain Fracture Toughness of AISI M2 Steel From Precracked Round-Bar Specimens," Eng. Fract. Mech., 2000, 65, pp. 559-72.
6. A. Bayram, A. Uguz, and M. Ula: "Effect of Microstructure and Notches on the Mechanical Properties of Dual-Phase Steels," Mater. Charact., 1999, 43, pp. 259-69.
7. A. Bayram and A. Uguz: "The Effect of a Notch on the Tensile Properties of a Commercial 7075-Al Alloy," Metall. 1999, 53(9), pp. 486-89.
8. A. Bayram and A. Uguz: "The Effect of Spheroidising and Na-Modification on the Mechanical Properties of Al-Si Cast Alloys," Metall., 1999, 53(3), pp. 131-34.
9. D.M. Li and A. Bakker: "Fracture Toughness Evaluation for an RSP Al Alloy Using Circumferentially-Cracked Cylindrical Bar Specimens," Eng. Fract. Mech., 1997, 57, pp. 1-11.
10. K. Kobayashi, H. Imada, and T. Majima: "Nucleation and Growth of Creep Voids in Circumferentially Notched Specimens," JSME Int. J.A.-Solid M., 1998, 41, pp. 218-24.
11. J. R. Donoso, F. Labbe, and H. Argomedo: "A Calibration Function for Notched Cylindrical Tension Specimens, Based on the Common Format Equation: Numerical and Experimental Data Analysis," Eng. Fract. Mech., 1996, 54, pp. 617-28.
12. J. Toribo: "A Fracture Criterion for High-Strength Steel Notched Bars," Eng. Fract. Mech., 1997, 57, pp. 391-404.
13. D.B. Lanning, G.K. Haritos, and T. Nicholas: "Influence of Stress State on High Cycle Fatigue of Notched Ti-6Al-4V Specimens," Int. J. Fatigue, 1999, 21(Suppl. S), pp. S87-S95.
14. A. Valiente and J. Lapena: "Measurement of the Yield and Tensile Strengths of Neutron-Irradiated and Post-Irradiation Recovered Vessel Steels With Notched Specimens," Nucl. Eng. Des., 1996, 167(1), pp. 11-22.
15. Anon: "ASTM Designation E602, Standard Method for Sharp-Notch Tension Testing With Cylindrical Specimens" in Annual Book of ASTM Standards, Part 3, American Society for Testing and Materials, Philadelphia, PA, 1988, pp. 964-972.
16. G.E. Dieter: Mechanical Metallurgy, SI edition, McGraw-Hill, Singapore, 1988, pp. 316 and 358.
17. P.C. Paris and G.C. Sih: "Stress Analysis of Cracks" in ASTM STP, No. 381, American Society for Testing and Materials, Philadelphia, PA, 1965, pp. 30-83.
18. M.A.N. Shabara, A.A. El-Domiaty, and M.D. Al-Ansary: "Estimation of Plane Strain Fracture Toughness From Circumferentially Bluntly Notched Round-Bar Specimens," Eng. Fract. Mech., 1996, 54, pp. 533-41.
19. 1C," Eng. Fract. Mech., 2000, 65, pp. 491-505.