Monolithic and composite ceramic machining flaw-microstructure-strength effects: Model evaluation

Journal of the European Ceramic Society

Volumn 22, Issue 9-10, 2002, Pages 1411-1424

  Rice, Roy W ^a  

^a NONE   (United States)

Author keywords

Composites; Flaws; Machining; Microstructural effects; Strength

Indexed keywords

ELASTIC MODULI; FRACTURE; GRAIN SIZE AND SHAPE; HARDNESS; MACHINING; MICROSTRUCTURE; PARTICLE SIZE ANALYSIS; POROSITY;

MACHINING FLAWS;

CERAMIC MATERIALS;

MACHINING;

EID: 0036722317     PISSN: 09552219     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0955-2219(01)00488-5     Document Type: Article

References (58)

1. Wear mechanisms in ceramics
2. Failure from surface flaws
3. The nature of machining damage in brittle materials
4. Grinding mechanisms and strength degredation for ceramics
5. Effect of stresses from thermal expansion anisotropy, phase transformations, and second phases on the strength of ceramics
6. Machining of ceramics
7. The effect of grinding direction on the strength of ceramics
8. Effect of flaw geometry and fracture of glass
9. Processing induced sources of mechanical failure in ceramics
10. The nature of strength controlling machining flaws in ceramics
11. Machining flaws and the strength-grain size behavior of ceramics
12. The effect of grinding direction on flaw character and strength of single crystal and polycrystalline ceramics
13. Ceramic fracture features, observations, mechanisms, and uses
14. Perspective on fractography
15. Effects of ceramic microstructural character on machining direction-strength anisotrophy
16. Correlation of machining- grain- size effects on tensile strength with tensile strength- grain-size behavior
17. Porosity effects on machining direction-strength anisotropy and failure mechanisms
18. A basic study of the diamond grinding of alumina
19. Processing defects in partially stabilized zirconia
20. Reliable ceramics for advanced heat engines
21. Fractographic analysis of machining cracks in silicon nitride rods and bars
22. Review, ceramic tensile strength: Grain size relations: Grain sizes, slopes, and branch intersections
23. Effect of microstructure on rate of machining of ceramics
24. Correlation of fracture toughness and strength
25. Relation of tensile strength-porosity effects in ceramics to porosity dependence of Young's modulus and fracture energy, porosity character and grain size
26. Strength-grain size relations in polycrystalline ceramics
27. A dimensional analysis of the grain-size dependence of strength
28. Grain-size dependence of strength
29. 4
30. Effect of surface finish on the strength of hot pressed silicon nitride
31. The influence of grinding on the flexural strength of ceramics
32. Diamond grinding of silicon nitride ceramic
33. 4 and aliminum iso-propoxide
34. Surface finish effects and the strength-grain size relation in SiC
35. Surface finish effects and the strength-grain size relationship in MgO
36. 3
37. Effect of surface finish on structural ceramic failure
38. Strengthening by surface damage in metastable tetragonal zirconia
39. Factors influencing the strength of a 95% alumina ceramic
40. Observations on mechanically abraded aluminum oxide crystals by transmission electron microscopy
41. Residual stresses in machined ceramic surfaces
42. Effect of residual stresses on the fracture of ground ceramics
43. Measurement of residual stresses in machined ceramics using the indentation technique
44. 4 grooved by single-point grinding
45. 3-SiC nanocomposites
46. Affect of grinding and polishing on near-surface phase transformation in zirconia
47. 3-TiC
48. Toughening in ceramic particulate and whisker composites
49. Some properties of two-phase crystal-glass solids
50. 4 without sintering aids
51. Microstructure and mechanical properties of hot pressed SiC-TiC composites
52. Hardness-grain-size relations in ceramics
53. The dependence of strength-controlling fracture energy on the flaw-size to grain-size ratio