Phase transformation and its effect on flank wear in machining steels

Journal of Manufacturing Science and Engineering

Volumn 124, Issue 3, 2002, Pages 659-666

  Kim, Wonsik ^a   Kwon, Patrick ^a  

^a Michigan State University   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

ABRASION; ANNEALING; CARBON STEEL; COMPOSITION; COOLING; CUTTING; INCLUSIONS; INTERFACES (MATERIALS); MARTENSITE; PHASE TRANSITIONS; SCANNING ELECTRON MICROSCOPY; STEEL; TRANSMISSION ELECTRON MICROSCOPY; X RAY DIFFRACTION ANALYSIS;

FLANK WEAR;

TURNING;

EID: 0036700224     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1473145     Document Type: Article

References (34)

1. Ramalingham, S., and Wright, P.K., 1981, "Abrasive Wear in Machining: Experiments With Materials of Controlled Microstructure," ASME J. Eng. Mater. Technol., 103, pp. 151-156.
2. Suh, N.P., 1986, Tribophysics, Prentice-Hall, Inc. New Jersey.
3. Hartung, P., and Kramer, B.M., 1982, "Tool Wear in Titanium Machining," CIRP Ann., 31, pp. 75-80.
4. Kramer, B.M., and Suh, N.P., 1980, "Tool Wear by Solution: A Quantitative Understanding," ASME J. Ind., 102, pp. 303-339.
5. Cook, N.H., and Nayak, P., 1966, "The Thermal Mechanics of Tool Wear," ASME J. Ind., 88(1), p. 63.
6. Kannatey-Asibu, E., 1985, "A Transport-Diffusion Equation in Metal Cutting and Its Application to Analysis of the Rate of Flank Wear," ASME J. Ind., 107, pp. 81-89.
7. Kramer, B.M., 1979, "An Analytic Approach to Tool Wear," Ph.D. thesis, MIT, Cambridge, MA.
8. Suh, N.P., and Fillion, P.D., 1980, "Optimization of Cutting Tool Properties Through the Development of Alumina Cermet," Wear, 62, pp. 132-137.
9. Kwon, P., 2000, "Predictive Models for Flank Wear on Coated Inserts," ASME J. Tribol., 122(1), pp. 340-347.
10. Kwon, P., and Kountaya, R.K., 1999, "Experimental Observation on Machining Spherodized Plain Carbon Steels," Tribol. Trans., 42, pp. 265-272.
11. Marinov, V., 1996, "Experimental Study of the Abrasive Wear in Metal Cutting," Wear, 197, pp. 242-247.
12. Ramanujachar, K., and Subramanian, S.V., 1996, "Micromechanics of Tool Wear in Machining Free Cutting Steels," Wear, 197, pp. 45-55.
13. Kwon, P., (formerly Judd, P.K.) 1985, "Theoretical Foundations for the Optimization of Ceramic Coated Tools," S.M. Thesis, MIT, Cambridge, MA.
14. Opitz, H., and Gappisch, M., 1962, "Some Recent Research on the Wear Behavior of Carbide Cutting Tools," Int. J. Mach. Tool Des. Res., 2, pp. 43-73.
15. Hau-Bracamonte, J.L., 1981, "Partial Austenization within Flow Zone When Cutting a Low-carbon Steel," Metals Technology, 8, pp. 447-450.
16. Hau-Bracamonte, J.L., and Wise, M.L.H., 1983, "Austenization of Steel during Chip Formation," Metall. Trans. A, 14A, pp. 1743-1745.
17. Shelbourn, A.M., Roberts, W.T, and Trent, E.M., 1985, "Structures of Machined Steel Chip," Match Sci. Technol., 1, pp. 220-226.
18. Littmann, W.E., and Wulff, J., 1955, "The Influence of the Grinding Process on the Structure of Harden Steels," ASM Trans. Q., 47, pp. 692-713.
19. Griffiths, B.J., 1985, "White Layer Formations at Machined Surfaces and Their Relationship to White Layer Formation at Worn Surfaces," ASME J. Tribol., 107, pp. 165-171.
20. Tönshoff, H.K., Wobsker, H.-G., and Brandt, D., 1995, "Hard Turning-Influences on the Workpiece Properties," Transactions of NAMRI/SME, XXIII, pp. 215-220.
21. Tönshoff, H.K., Wobsker, H.-G., and Brandt, D., 1995, "Tribological Aspect of Hard Turning with Ceramic Tools," Lubr. Eng., 51(2), pp. 163-168.
22. Matsumoto, Y., Barash, M.M., and Liu, C.R., 1987, "Cutting Mechanism During Machining of Hardened Steel," Mater. Sci. Technol., 3, pp. 299-305.
23. Shaw, M.C., and Vyas, A., 1994, "Heat-Affected Zones in Grinding Steel," CIRP Ann., 43(1), pp. 279-282.
24. Snoeys, R., Leuven, K.U., Maris, M., Peters, N.F., Peters, N.F., and Leuven, K.U., 1978, "Thermally Induced Damage in Grinding," CIRP Ann., 27(2), pp. 571-581.
25. Kruth, P., Stevens, L., Froyen, L., and Lauwers, B., 1995, "Study of the White layer of a Surface Machined by Die-Sinking Electro-Discharge Machining," CIRP Ann., 44(1), pp. 165-171.
26. Chou, Y.K., and Evans, C.J., 1998, "Process Effects on White Layer Formation in Hard Turning," Transactions of NAMRI/SME, XXVI, pp. 117-122.
27. Chou, Y.K., and Evans, C.J., 1999, "White Layer And Thermal Modeling of Hard Turned Surface," Int. J. Mach. Tools Manuf., 39, pp. 1863-1881.
28. Akcan, S., Shah, S., Moylan, S.P., Chhahra, P.N., Chandrasekar, S., and Farris, T.N., 1999, "Characteristic of White Layers Formed in Steels by Machining," Proceedings of ASME, IMECE, Nashville, TN.
29. Okusa, K., Takahashi, H., and Nishizawa, M., 1978, "Behavior of White Layer During Cutting of iron and Steels," Bull. Jpn. soc. Precis. Eng., 12(4), pp. 171-176.
30. Kim, S., and Durham, D.R., 1991, "Microscopic Studies of Flank Wear on Alumina Tools," ASME J. Tribol., 113, pp. 204-209.
31. Shaw, M.C., 1992, Metal Cutting Principles, Clarendon Press, Oxford.
32. Dearnley, P.A., 1985, "Rake and Flank Wear Mechanisms of Coated and Uncoated Cemented Carbides," ASME J. Ind., 107, pp. 68-82.
33. Callister, W.D.J., 1994, Materials Science and Engineering: An Introduction, 3rd ed. John Wiley & Sons, Inc, New York, NY.
34. Devires, W.R., 1991, Analysis of Material Removal Processes, Springer-Verlag, New York, NY.