Weight function analysis on the R-curve behavior of multilayered alumina-zirconia composites

Journal of the American Ceramic Society

Volumn 85, Issue 6, 2002, Pages 1505-1511

  Moon, Robert J ^a   Hoffman, Mark ^a,d   Hilden, Jon ^b   Bowman, Keith ^b,d   Trumble, Kevin ^b,d   Rödel, Jürgen ^c,d  

^a UNIVERSITY OF NEW SOUTH WALES   (Australia)

^b PURDUE UNIVERSITY   (United States)

^c DARMSTADT UNIVERSITY OF TECHNOLOGY   (Germany)

^d AMERICAN CERAMIC SOCIETY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

ALUMINA; COMPOSITION EFFECTS; CRACK PROPAGATION; FRACTURE MECHANICS; NOTCHED BAR TENSILE TESTING; POROSITY; RESIDUAL STRESSES; SINTERING; STRESS CONCENTRATION; THICKNESS MEASUREMENT; ZIRCONIA;

SINGLE EDGE NOTCHED BEAM TESTING GEOMETRY; WEIGHT FUNCTION ANALYSIS;

COMPOSITE MATERIALS;

EID: 0036607576     PISSN: 00027820     EISSN: None     Source Type: Journal    
DOI: 10.1111/j.1151-2916.2002.tb00304.x     Document Type: Article

References (41)

1. Toughening of layered ceramic composites with residual surface compression
2. Toughening of layered ceramic composites with residual surface compression: Effects of layer thickness
3. 3
4. Crack deflection in ceramic/ceramic laminates with strong interfaces
5. Crack deflection at an interface between dissimilar elastic materials: Role of residual stress
6. Laminar ceramics that exhibit a threshold strength
7. 3/Ce-TZP layered micro-composites
8. 3
9. A comparison of R-curves from SEVNB and SCF fracture toughness test methods on multilayered alumina-zirconia composites
10. Fracture resistance curve behavior of multilayered alumina-zirconia composites produced by centrifugation
11. Static fracture behavior of multilayer alumina-zirconia composites
12. 2 composite slurries vs interparticle potentials: Particle packing and mass segregation
13. Alumina of high reliability by centrifugal casting
14. 3 slurries vs interparticle potential
15. Influence of residual stresses on the mechanical properties of a layered ceramic composite
16. New method for efficient colloidal particle packing via modulation of repulsive lubrication hydration forces
17. Fracture toughness using the SEVNB method: Preliminary results
18. Method for measuring short-crack R-curves without calibration parameters: Case studies on alumina and alumina/aluminum composites
19. A novel principle for the computation of stress intensity factors
20. Influence of crack-surface interactions on stress intensity factor in ceramics
21. Determination of fracture toughness at high temperature after subcritical crack extension
22. Determination of residual stresses in components using the fracture mechanics weight function
23. Direct adjustment procedure for weight function analysis of graded materials
24. 3/Al FGMs
25. R-curve behavior in alumina-zirconia composites with repeating graded layers
26. Creep of duplex microstructures
27. Constrained densification of alumina/zirconia hybrid laminates: II, viscoelastic stress computation
28. Crack-interface grain bridging as a fracture resistance mechanism in ceramics: II, theoretical fracture mechanics model
29. Role of interfacial grain-bridging sliding friction in the crack-resistance and strength properties of nontransforming ceramics
30. R-curve behavior of long cracks in alumina
31. In situ measurements of bridged crack interfaces in the scanning electron microscope
32. Grain-bridging mechanisms in monolithic alumina and spinel
33. Analytical modeling for bridging stress function involving grain size distribution in a polycrystalline alumina
34. On the quantification of bridging tractions during subcritical crack growth under monotonic and cyclic fatigue loading in a grain-bridging silicon carbide ceramic
35. The mechanical theory of equilibrium cracks in brittle fracture
36. R-curve behavior of duplex ceramics
37. Evaluation of bridging parameters in aluminas from R-curves by use of the fracture mechanical weight function
38. 3
39. Design and properties of multilayered ceramic composites
40. Cracking of laminates subjected to biaxial tensile stresses
41. Evaluated material properties for a sintered α-alumina