Stress development in drying coatings after solidification

AIChE Journal

Volumn 48, Issue 3, 2002, Pages 437-451

  Lei, H ^a,b   Francis, L F ^a   Gerberich, W W ^a   Scriven, L E ^a  

^a UNIVERSITY OF MINNESOTA   (United States)

^b EASTMAN KODAK COMPANY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTER SIMULATION; CREEP; DEFORMATION; DIFFUSION; DRYING; MASS TRANSFER; SHRINKAGE; SOLIDIFICATION; STRESSES;

VISCOUS CREEP;

PLASTIC COATINGS;

POLYMER;

CREEP; DRYING; POLYMER COATING; SHRINKAGE; SOLIDIFICATION; STRESS;

ADHESION; ARTICLE; DIFFUSION; ELASTICITY; EVAPORATION; FINITE ELEMENT ANALYSIS; FLOW; LIQUID; MASS; MATERIAL COATING; SOLID; STRESS; VISCOSITY;

EID: 0036524880     PISSN: 00011541     EISSN: None     Source Type: Journal    
DOI: 10.1002/aic.690480304     Document Type: Article

References (39)

1. Billovits, G. F., and C. J. Durning, "Polymer Material Coordinates for Mutual Diffusion in Polymer Penetrant Systems," Chem. Eng. Commun., 82, 21 (1989).
2. Bornside, D. E., "Spin Coating," PhD Thesis, Univ. of Minnesota (1988).
3. Bornside, D. E., "Mechanism for the Local Planarization of Microscopically Rough Surfaces by Drying thin Films of Spin-Coated Polymer/Solvent Solutions," J Electrochem. Soc., 137, 2589 (1990).
4. Cairncross, R. A., L. F. Francis, and L. E. Scriven, "Competing Drying and Reaction Mechanisms in the Formation of Sol-to-Gel Films, Fibers, and Spheres," Drying Technol., 10, 893 (1992).
5. Christodoulou, K. N., E. J. Lightfoot, and R. W. Powell, "Model of Stress-Induced Defect Formation in Drying Polymer Films," AIChE J., 44, 1484 (1998).
6. Corcoran, E. A., "Determining Stresses in Organic Coatings Using Plate Beam Deflection," J. Paint Technol., 41, 635 (1969).
7. Crank, J., The Mathematics of Diffusion, Clarendon Press, Oxford (1975).
8. Croll, S. G., "Internal Stress in a Solvent-Cast Thermoplastic Coating," J. Coat. Tech., 50, 33 (1978).
9. Croll, S. G., "The Origin of Residual Internal Stress in Solvent-Cast Thermoplastic Coatings," J. Appl. Polym. Sci., 23, 847 (1979).
10. Dafalias, Y. F., "The Plastic Spin," J. Appl. Mech., 52, 865 (1985).
11. Durning, C. J., "Mutual Diffusion in Concentrated Polymer Solutions Under a Small Driving Force," Macromolecules, 19, 2220 (1986).
12. Gutoff, E. B., and E. D. Cohen, Coating and Drying Defects: Troubleshooting Operation Problems, Wiley, New York (1995).
13. Hasatani, M., and Y. Itaya, "Fundamental Study on Shrinkage of Formed Clay During Drying-Viscoelastic Strain-Stress and Heat/Moisture Transfer," Drying Technol., 10, 1013 (1992).
14. Hasatani, M., Y. Itaya, and K. Muroie, "Contraction Characteristics of Molded Ceramics During Drying," Drying Technol., 11, 815 (1993).
15. Irudayaraj, J., and K. Haghighi, "Stress Analysis of Viscoelastic Materials During Drying," Drying Technol., 11, 901 (1993).
16. Itaya, Y., S. Mabuchi, and M. Hasatani, "Deformation Behavior of Ceramics Slabs by Nonuniform Drying," Drying Technol., 13, 801 (1995).
17. Larche, F. C., and J. W. Cahn, "A Linear Theory of Thermochemical Equilibrium of Solids Under Stress," Acta. Metall., 21, 1051 (1973).
18. Larche, F. C., and J. W. Cahn, "The Effect of Self-Stress on Diffusion in Solids," Acta. Metall., 30, 1835 (1982).
19. Lee, E. H., "Elastic-Plastic Deformation at Finite Strains," J. Appl. Mech., 91, 1 (1969).
20. Lee, R. L., P. M. Gresho, and R. L. Sani, "Smoothing Techniques for Certain Primitive Variable Solutions of the Navier-Stokes Equation," Int. J. Num. Meth. Eng., 14, 1785 (1979).
21. Lei, H., "Flow, Deformation, Stress and Failure in Solidifying Coatings," PhD Thesis, Univ. of Minnesota (1999).
22. Lei, H., J. A. Payne, L. F. Francis, A. V. McCormick, W. W. Gerberich, and L. E. Scriven, "Stress Development in Drying Coatings," J. Appl. Poly. Sci., 81, 1000 (2001).
23. Li, J. C. M., R. A. Oriani, and L. S. Darken, "The Thermodynamics of Stressed Solids," Z. Physik. Chem. Neue Folge, 49, 271 (1966).
24. Li, J. C. M., "Chemical Equilibrium in a Stressed Polymers," J. Appl. Phys., 42, 4543 (1971).
25. Lubliner, J., Plasticity Theory, Macmillan, New York (1990).
26. Malvern, L. E., Introduction to the Mechanics of a Continuous Medium, Prentice-Hall, Englewood Cliffs, NJ (1969).
27. Moran, B., M. Ortiz, and C. F. Shih, "Formulation of Implicit Finite Element Methods for Multiplicative Finite Deformation Plasticity," Int. J. Num. Meth. Eng., 29, 483 (1990).
28. Owen, D. R. J., and E. Hinton, Finite Elements in Plasticity: Theory and Practice, Pineridge Press Ltd., Swansea, U. K. (1980).
29. Payne, J. A., "Stress Evolution in Solidifying Coatings," PhD Thesis, Univ. of Minnesota (1998).
30. Perera, D. Y., and D. V. Eynde, "Considerations on a Cantilever (Beam) Method for Measuring the Internal Stress in Organic Coatings," J. Coat. Tech., 53(677), 39 (1981).
31. Peurrung, L. M., and D. B. Graves, "Film Thickness Profiles over Topography in Spin Coating," J. Electrochem. Soc., 138, 2115 (1991).
32. Rivlin, R. S., and D. W. Saunders, "Large Elastic Deformations of Isotropic Materials: Experiments on the Deformation of Rubber," Phil. T. Roy. A, 243, 251 (1951).
33. Schunk, P. R., and R. R. Rao, "Finite Element Analysis of MultiComponent Two-Phase Flows with Interphase Mass and Momentum Transport," Int. J. Num. Meth. Fluids, 18, 821 (1994).
34. Tam, S. Y., L. E. Scriven, and H. K. Stolarski, "Stress Effects in Drying Polymer Films," Mater. Res. Soc. Symp. Proc., 356, 547 (1995).
35. Tam, S. Y., "Stress Effects in Drying Coatings," PhD Thesis, University of Minnesota (1997).
36. Vergne, D. B. L., and D. C. Hofer, "Modeling Planarization with Polymers," Proc. Soc. Photo., 539, 115 (1985).
37. White, L. K., "Planarization Properties of Resist and Polyimide Coatings," J. Electrochem. Soc., 130, 1543 (1983).
38. Wilson, R. H., and P. A. Piacente, "Effect of Circuit Structure on Planarization Resist Thickness," J. Electrochem. Soc., 133, 981 (1986).
39. Wu, Q., and M. R. Milota, "Effect of Creep and Mechano-Sorptive Effect on Stress Development During Drying," Drying Technol., 12, 2057 (1994).