Crack path selection in adhesively bonded joints: The roles of external loads and speciment geometry

International Journal of Fracture

Volumn 114, Issue 2, 2002, Pages 167-190

  Chen, Buo ^a,e   Dillard, David A ^b   Dillard, John G ^c   Clark Jr , Richard L ^d  

^a Mechanical Engineering   (United States)

^b Materials Science and Tire Mechanics   (United States)

^c Chemistry Department   (United States)

^d Materials Science and Engineering   (United States)

^e California Consortium for Engineering Advances in Technological Education   (United States)

Author keywords

Adhesively bonded joints; Cohesive failure; Crack path selection; Directional stability of cracks; Failure mode; Interfacial failure; Locus of failure; Mixed mode fracture; T stress; XPS surface analysis

Indexed keywords

ADHESIVE JOINTS; AUGER ELECTRON SPECTROSCOPY; CANTILEVER BEAMS; CRACK PROPAGATION; EPOXY RESINS; FAILURE (MECHANICAL); FAILURE ANALYSIS; FINITE ELEMENT METHOD; IMPACT TESTING; LOADS (FORCES); SCANNING ELECTRON MICROSCOPY; STRESS ANALYSIS; SURFACE PHENOMENA; X RAY PHOTOELECTRON SPECTROSCOPY;

MIXED MODE FRACTURES;

FRACTURE MECHANICS;

ADHESIVE WEAR; ALUMINUM; CRACK INITIATION; EPOXY RESIN; FRACTURE MECHANICS; GEOMETRY; JOINT;

EID: 0036506952     PISSN: 03769429     EISSN: None     Source Type: Journal    
DOI: 10.1023/A:1015020919823     Document Type: Article

References (45)

1. Analysis of a wavy crack in sandwich specimens
2. Brittle fracture of adhesive joints
3. The calculation of adhesive fracture energies from double-cantilever beam test specimens
4. The failure of fibre composites and adhesively bonded fibre composites under high rates of test, part I mode I loading - Experimental studies
5. The failure of fibre composites and adhesively bonded fibre composites under high rates of test, part II mode I loading - Dynamic effects
6. The failure of fibre composites and adhesively bonded fibre composites under high rates of test, part III mixed-mode I/II and mode II loadings
7. The characterization of mode I delamination failure in non-woven, multidirectional laminates
8. On the correlation between the mode I fracture of adhesive joints and laminated composites
9. A note on crack trajectory in an elastic strip bounded by rigid substrates
10. On the failure of cracks under mixed-mode loads
11. Numerical analysis of the directionally unstable crack propagation in adhesively bonded joints
12. The effect of the T-stress on the crack path selection in adhesively bonded joints
13. Crack path selection in adhesively bonded joints: The role of material properties
14. Slightly curved or kinked cracks
15. Effect of thermal residual stress on the crack path in adhesively bonded joints
16. Measurement of residual stresses and thermal expansion in adhesive bonds
17. Analysis of the notched coating adhesion test
18. On crack extension in plates under plane loading and transverse shear
19. Crack path selection in a brittle adhesive layer
20. Crack propagation at and near bimaterial interfaces: Linear analysis
21. Brittle fracture of solids with arbitrary cracks
22. Mixed mode cracking in layered materials
23. Toughening mechanisms in mixed-mode interfacial fracture
24. On the use of laminated beams for the determination of pure mixed-mode fracture properties of structural adhesives
25. Nonlinear effects in mixed-mode interfacial delaminations
26. Similarity concepts in the fatigue fracture of adhesively bonded joints
27. On the problem of crack extension in brittle solids under general loading
28. Environmental aging of the Ti-6Al-4V/FM-5 polyimide adhesive bonded system: Implications of physical and chemical aging on durability
29. Effect of mode mixity on the fracture toughness of Ti-6A1-4V/FM-5 adhesive joints
30. An investigation into dynamic fracture. I - Crack initiation and arrest
31. An investigation into dynamic fracture. II - Microstructural aspects
32. An investigation into dynamic fracture. III - On steady-state crack propagation and branching
33. An investigation into dynamic fracture. IV - On the interaction of stress wave with propagating cracks
34. An unsymmetric double cantilever beam test for interfacial fracture toughness determination
35. Interface crack between two elastic layers
36. Asymmetric shielding mechanisms in the mixed-mode fracture of a glass/epoxy interface
37. Intrinsic toughness and adhesion mechanisms of glass/epoxy interface
38. Fracture of a model interface under mixed-mode loading
39. The influence of curing agent content on the mechanical and adhesive properties of Dicyandiamide cured epoxy systems
40. On the stress distribution at the base of a stationary crack
41. Analysis of a mixed mode fracture specimen: The asymmetric double cantilever beam