Rapidly solidified powder metallurgy Mg97Zn1Y2 alloys with tensile yield strength of 610 MPa and elongation of 5%

TMS Annual Meeting

Volumn , Issue , 2002, Pages 227-232

  Kawamura, Yoshihito ^a   Inoue, Akihisa ^b  

^a KUMAMOTO UNIVERSITY   (Japan)

^b TOHOKU UNIVERSITY   (Japan)

Author keywords

[No Author keywords available]

Indexed keywords

MAGNESIUM POWDER METALLURGY; NANOSTRUCTURED MATERIALS; STRAIN; SUPERPLASTICITY; TENSILE STRENGTH;

PLASTIC STRAIN;

MAGNESIUM ALLOYS;

EID: 0036459891     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (15)

1. F.H. Frees and S.J. Savage, ed., Processing of Structural Metals by Rapid Solidification (Metals Park, Ohio, ASM International, 1987), 367-415.
2. A. Kato et al., "Consolidation and Mechanical Properties of Atomized Mg-Based Amorphous Powders," Mater. Sci. Eng., A179/A180 (1994), 112-117.
3. Y. Kawamura et al., "High Strength Nanocrystalline Mg-Al-Ca Alloys Produced by Rapidly Solidified Powder Metallurgy Processing," Mater. Sci. Forum, 350-351 (2000), 111-116.
4. K. Hayashi et al.," Structure and Mechanical Properties of Rapidly Solidified Mg-X Alloys," Mater. Sci. Forum, 350-351 (2000), 117-122.
5. K. Hayashi, "Development of Rapidly Solidified Powder Metallurgy Magnesium Alloys With High Strength" (Master thesis, Tohoku University, 2001).
6. 2 Alloys with Excellent Tensile Yield Strength above 600 MPa," Mater. Trans., 42 (2001), 1172-1176.
7. Y. Kawamura et al., "High-Strength Powder Metallurgy Aluminum Alloys in Glass-Forming Al-Ni-Ce-(Ti or Zr) Systems," Scripta Metall. Mater., 29 (1993), 275-280.
8. Y. Kawamura et al., "Rapidly Solidified Powder Metallurgy Al-Ti-Fe Alloys," Scripta Metall. Mater., 37 (1997), 205-210.
9. Y. Kawamura, A. Inoue and T. Masumoto, "Mechanical Properties of Amorphous Alloy Compacts Prepared by a Closed Processing System," Scripta Metall. Mater., 29 (1993), 25-30.
10. Y. Kawamura et al., "High-Strength Crystalline Aluminum Alloys Produced from Amorphous Powders by a Closed P/M Processing," Mater. Trans., JIM, 34 (1993), 969-975.
11. Y. Kawamura et al., "Fabrication of Bulk Amorphous Alloys by Powder Consolidation," Int. J. Powder. Metallurgy, 33 (1997), 50-61.
12. A. Kato, "Production of Rapidly Solidified Magnesium Alloy Powders and Mechanical Properties of their Extruded Alloys" (ph.D. thesis, Tohoku University, 1994).
13. T. Sakuma, "A Brief Review on the Project "Towards Innovation in Superplasticity"," Mater. Sci. Forum, 304-306 (1999), 3-10.
14. th JIM Annual Meeting, Fukuoka, Japan, 24 September 2001).
15. th JIM Annual Meeting, Fukuoka, Japan, 22 September 2001).