On-line processing of unidirectional fiber composites using radiative heating: I. Model

Journal of Composite Materials

Volumn 36, Issue 16, 2002, Pages 1905-1934

  Chern, Bih Cherng ^a   Moon, Tess J ^a   Howell, John R ^a  

^a The University of Texas at Austin   (United States)

Author keywords

Composite processing; Continuous curing; Cylinder; Degree of cure; Epoxy resin; In situ curing; Infrared heating; Modeling; On line consolidation; Polymer composite

Indexed keywords

BOUNDARY CONDITIONS; COMPUTER SIMULATION; CURING; EPOXY RESINS; HEAT FLUX; HEAT RADIATION; INFRARED HEATING; LAMINATED COMPOSITES; MATHEMATICAL MODELS; THERMOPLASTICS; THERMOSETS;

COMPOSITE PROCESSING;

FIBER REINFORCED PLASTICS;

EID: 0036362025     PISSN: 00219983     EISSN: None     Source Type: Journal    
DOI: 10.1177/0021998302036016236     Document Type: Article

References (39)

1. The effects of mandrel material and tow tension on defects and compressive strength of hoop-wound, on-line consolidated, composite rings
2. Compressive strengths of in-situ cured graphite/epoxy and glass/epoxy composite cylinders
3. On-line processing of unidirectional fiber composites using radiative heating: II. Radiative properties, experimental validation and process parameter selection
4. Continuous curing and induced thermal stresses of a thick filament wound composite cylinder
5. Process-induced residual stresses in a continuously-cured, hoop-wound thermoset composite cylinder, Part I: Theory; Part II: Validation; Part III: Processing variable study
6. Dependent scattering of an oblique incident plane wave by a collection of parallel cylinders
7. Dependent radiative transfer regime for unidirectional fiber reinforced composites upon normal incident radiation
8. Radiative transfer in porous media, chapter 15
9. Assessment of using in-situ IR-heat to cure thermoset, filament-wound structures
10. Modeling of radiation-initiated cure-on-the-fly of epoxy-matrix composite cylinders
11. Thermal analysis of in-situ curing for thermoset, hoop-wound structures using infrared heating: Part I: Predictions assuming independent scattering
12. Thermal analysis of in-situ curing for thermoset, hoop-wound structures using infrared heating: Part II: Dependent scattering effect
13. Thermal analysis and process window development for the in-situ curing of thermoset composites
14. Effects of process variables on in-situ curing for thick composites using infrared heating
15. The simultaneous process of filament winding and curing for polymer composites
16. Continuous curing process for thermoset polymer composites. Part 1: Modeling and demonstration
17. Optical constants of carbons and coals in the infrared
18. Thermal radiative properties of glass from 0.32 to 206 μm
19. Effect of fiber orientation on thermal radiation in fibrous media
20. Dependent versus independent scattering in fibrous composites containing parallel fibers
21. Mixed convection from an arbitrarily inclined semi-infinite flat plate - I. The influence of the inclination angle
22. Convection from an isolated heated horizontal cylinder rotating about its axis
23. Heat transfer from a rotating cylinder with and without crossflow
24. Free convection heat transfer from a rotating horizontal cylinder to ambient air with interferometric study of flow
25. Three-dimensional radiative heat-transfer solutions by the discrete-ordinates method
26. Three-dimensional spectral radiative heat transfer solutions by the discrete-ordinates method
27. New experimental data for enthalpy of reaction, and temperature- and degree-of-cure-dependent specific heat and thermal conductivity of the Hercules 3501-6 epoxy system
28. Heat of reaction, degree of cure, and viscosity of Hercules 3501-6 resin
29. Modeling of processing of composites part II temperature distribution during cure
30. Thermal modeling of tape laying with continuous carbon fibre-reinforced thermoplastic
31. Thermal conductivity of unidirectional materials